Model #79046813991 KENMORE ELITE Slide-In Range, Electric/Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a kenmore elite duel fuel stove and the model number is 79046813991 and It did not come with installation instructions or LP conversion kit ( part number

A:

I am sorry to hear that you are experiencing these difficulties with your Kenmore Elite dual fuel stove.The Managemylife web site is a good resource of information to find out what may be happening and what options are available to you. I did some research at Managemylife website and found this expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. I also found this manual that may help.

Read More
James -
December 05, 2012
A:

Thank you for your question and I understand your concern.

The LP kit is part number 318127414 which can be ordered at Sears Parts Direct and it should come with the installation instructions.

Read More
Joey S -
Sears Technician
December 06, 2012
A:

thanks

Read More
terri -
December 09, 2012
See more answers
Q:

Kenmore model 79046813991 Range, oven will not start. Gives me code F1. Is this a sensor Problem? What part do I need ? Can I install?

A:

I understand inconvenient it can be to have an error code on your appliance, especially an appliance you use for cooking. While you are waiting for an expert answer, I did manage to find a link about a similar problem. If you do decide you need a part I also added another link in where you add your model number and you can find most parts. I hope my links are useful.

Read More
Joseph P. -
August 31, 2010
A:

The "F1" fault code generally implies an oven control board failure however you would need to remove and test the oven temperature sensor first. The oven temperature sensor should measure approximately 1100 ohms at room temperature. The sensor can likely be removed and disconnected from inside the oven cavity. If the oven sensor measures approximately 1100 ohms, replace the oven control board. You should find the oven sensor located protruding into the oven cavity from the back wall in the upper left rear or upper right rear corner fastened by two screws. Remove the screws and pull the sensor out and disconnect the harness connector. Use an ohm meter to test the resistance.

I you find that the sensor is okay then I would call a technician to remove and replace the oven control board. The console must be taken off in order to access and remove the oven control board. The console is attached by screws on each side. NOTE: Disconnect the power supply from the range before removing the console.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
September 01, 2010
See more answers
Q:

does range model 79046813991 take 220 wiring

A:

Installing an appliance without the proper information makes the job harder. I did find a similar question and attached that expert answer below. I also attached the link to your model range. Hope this helps while you wait for the expert answer.

Read More
Barbara H. -
July 22, 2010
A:

This dual fuel range will require 220 volt AC wiring since the oven has electric elements. I don't have the installation guide available online. I recommend that you order the installation manual (part 318104607) from the Sears PartsDirect website. Use the installation manual to properly install the range.

An electrician will need to install a 220 volt AC outlet for this range. Here is a link for the Service Live.com website that has contractors in most areas that can perform this service for you: ServiceLive.com .

Read More
Lyle W -
Sears Technician
July 23, 2010
See more answers

Top Parts