Model #79046769901 KENMORE Slide-In Range, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

kenmore electric stove 79046769901 Kenmore Electric range

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you.  I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

If the temperature from the range or cooktop gets too hot, the exhaust fan will automatically come on and could stay on for up to an hour. During this time, it cannot be turned off. If this is not the case, a technician will be needed to check it.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
Samantha A -
Sears Technician
October 14, 2014
A:

The board blink code f10?

Read More
rodolfo -
October 14, 2014
See more answers
Q:

Oven & Broiler won't work 79046769901 Kenmore Electric range

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Yadira B -
February 11, 2013
A:

Thank you for your question and I understand your concern.

 Key#119 on the "Body" page is the high limit/safety thermostat and is located under the top and is mounted on the top of the cooling fan duct. See image below.

If it trips open, the oven heating elements will not work. This thermostat trips when an overheating condition occurs. This helps protect vital electronic and electrical components.

The fix consists of adding a second thermostat that will turn on the cooling fan when the burner box area reaches a set temperature.

I added an image to reference below. The part number of the kit is 903169-9010 which can be ordered from SearsPartsDirect. 

 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 12, 2013
A:

Hi Joey, You were right on with the open high limit thermostat causing the problem. I ordered a new one and also ordered the second thermostat as you suggested. You mentioned a diagram attached to your response on how to instal the 2nd thermostat. I could not find the link to open it. Could you email that diagram to me. I would greatly appreciate it. Thank you in advance, Ed email--kezarpond@gmail.com

Read More
Ed -
April 02, 2014
See more answers
Q:

My oven won't heat up at all on "bake" and "broil" conditions

A:

I understand that your oven is not heating when it is set to bake or broil. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
May 22, 2012
A:

Thank you for your question and I understand your concern.

If the surface elements will continue to operate then there are likely one of two possible failures. If the oven quit heating after placing the oven in a self clean cycle; it may have a tripped thermal circuit breaker located on the rear of the range.

If you hadn't placed the oven in a self clean cycle; I suspect a faulty electronic oven control board.

The parts image does not show the thermal circuit breaker nor does it provide a part number but the wiring diagram shows it to have one. The thermal circuit breaker is generally located on the back of the range behind the panel. The thermal circuit breaker will have two (2) brown wires attached to it.

In order to diagnose which of the two components may have failed will require accessing the back of the range and removing the back panel. The thermal circuit breaker likely has a button in the center of the thermal circuit breaker to push which will reset the thermal circuit breaker. If the button does not appear to push in, the two wires should be disconnected from the thermal circuit breaker and it should be tested for continuity with an Ohm meter. If the thermal circuit breaker measures continuity, the electronic oven control is likely faulty. The electronic oven control double line break relay must close or the bake and broil element will not get the line 2 voltage supply. The bake and broil elements require 220 volts in order to heat. I added an image of the wiring diagram to reference below.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

NOTE: Disconnect the range from the power supply before servicing your range.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
May 23, 2012
A:

my bake an broil will not work as well when I did the instructions they came back F11 that was not the problem.. we have had the stove only a little over a year and I am very discouraged with it...we will try the suggestion above ..we ordered a new board that did not help now Sears refuses to let me return it...May be time to switch brands....

Read More
Wanda -
January 03, 2013
A:

Wanda: I must assume you have the same model range. If replacing the electronic oven control/clock assemby did not repair the failure, It sounds like the oven control is not getting line one and line two voltages or there is burnt wire common to both bake and broil circuit. The bake and broil element must have 220 volt power supply or they will not heat. I suggest calling a service technician to diagnose and repair your range. He can also check to see if the new board is faulty or not too.

Read More
Joey S -
Sears Technician
January 04, 2013
See more answers

Top Parts