Model #79046594502 KENMORE Slide-In Range, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

stove top stopped working

A:

Hi Victor! Sorry to read that the stove top is not working, however i would like to recommend finding a technician it could be the control panel, the wiring harness, the terminal block, or even the thermostat. It could be expensive trying to figure it out without a technician and at least you would have a full diagnostic it could be a simple a a 20 dollar part. Anyway i wish you the best of luck with your stove, an expert will be getting to you with in 2 business days.

Read More
The Harbinger -
November 05, 2013
A:

Thank you for your question and I understand your concern.

If the oven control/clock is operating and you are able to program the oven and it heats, then we know the range is getting the proper voltage supply of 220 volts. It would be very odd to have all the 4 radiant surface elements quit heating all at the same time unless it has loose or burnt wire connection in the line one (L1) or line two (L2) voltage supply supplying the voltage to the surface elements.

Since the top can be removed as an assembly, there is a quick disconnect harness connection that will need to be checked for any burnt or darkened wires. I added three images below with the procedure of removing the burner box assembly so you can check the wiring connections. NOTE: Locate the two house circuit breakers dedicated for the range and flip both breakers off before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
November 06, 2013
See more answers
Q:

Kenmore electric cook top oven shorted out. Won't work.

A:

 Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Yadira B -
August 08, 2013
A:

Thanks for contacting manage my life about your range/oven model 790.46594502; sorry you are having a problem. The pop you heard could have been from the element, its wiring or the main control board. These components will need to be tested. You will need a high quality volt ohm meter to perform the testing and a basic knowledge of electrical circuits. _Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product_I have attached the wiring diagram for the bake broil circuits, the element should be supplied with 240 volts ac = - 5% when the oven is set to operate. I would suggest you start the voltage test at the control board and work to the elements themselves. If you do not feel confident in your knowledge or do not have the needed equipment you should call for service. Here is a link to Sears Services. Ron H.

Read More
Ron H -
Sears Technician
August 09, 2013
A:

So, what will testing the voltage tell us? Which component is no good and needs to be replaced? Thanks, Ron.

Read More
Amy -
August 12, 2013
A:

Hi Amy, thanks for your reply about testing your oven wiring and control. If you test the components you will be able to determine if they are good or bad. You should read the voltage with a volt ohm meter between BA and OUT on the control (with it set to bake) 240lts ac + -. If you are not then the control is bad. If you do have this voltage then you know to track the voltage to the bake element where you should read the 240 volts ac + - , if there is voltage to the element and it does not heat it is bad. Use the diagram I have provided and use safety precautions and protective equipment. Ron H.

Read More
Ron H -
Sears Technician
August 12, 2013
See more answers

Top Parts