Model #79046593503 KENMORE Slide-In Range, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

I need to replace one the wiring harnesses in my kenmore electric oven/stove ((Model #790.46593503), and am not sure which of the four available harnesses it is

A:

I know how important it is to get the correct parts for your range to get it working properly once again. Instead of spending money on a part that may not fix the range I suggest you have a certified technician come out and check whats wrong with your range. I am adding a link below in where you can set service. I hope this helps with your range troubles while you wait for your expert response.

Read More
Joseph P. -
August 30, 2012
A:

It appears that you may need to the Timer wiring harness (part 318224810) but there is no way to be sure. The wire harnesses are not illustrated and the descriptions are not specific. Instead of replacing the entire wire harness, you can consider replacing just the damaged wire and connecting the wire using ceramic wire nuts or other connectors that you should be able to find at a local electrical supply or hardware store. Be sure that you shut off the house circuit breaker for the range before accessing internal components.

I posted the wiring diagram for that range in the image below. That information may help you if you decide to repair the harness instead of replacing it.

If you need to order that replacement harness and you think that the Timer is the one that you need, then you can order it through this page: Timer Harness for Kenmore Range Model 790.46593503 .

If you need more help, reply with additional details.

If you get to the point where you need to have a service technician examine and repair the wiring in that range, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 04, 2012
A:

Thank you, Lyle. I've discovered that it definitely was the Harness for the timer. That harness, however, plugs into another harness that was also burned-up. This harness routes to the rear back of the oven to the main power source. I think it's the "main harness". Does the Main Harness bifurcate into two separate harnesses at the main board? I'm thinking so. I went ahead and ordered the Main Harness and the Harness for the timer.

Read More
Michael -
September 04, 2012
A:

I am pretty sure that you are correct about that main wiring harness. Hopefully, those 2 harnesses should be what you need to complete that repair.

Read More
Lyle W -
Sears Technician
September 04, 2012
See more answers
Q:

left front burner

A:

With the burner on your rang not working after parts replaced can be frustrating. I have done some research on the Manage My life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert i have provided the link below. Hope this helps!

Read More
Priscilla V -
May 27, 2012
A:

Thank you for your question and I understand your concern.

It's normal for the radiant burner to cycle off and on. Place a flat bottom pan on the burner and it will likely remain on until the thermal limiter opens and causes the element to turn off. When the thermal limiter cools and closes, the radiant burner will come on again. It is very important to have a pot or pan on the burner in order to transfer heat or it will cycle off and on by the thermal limiter. The burner switch will also cycle the radiant burner off and on to regulate temperature. Since you have replaced the burner switch and the burner, I would have to assume it is working correctly.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 29, 2012
See more answers
Q:

Kenmore oven code F93

A:

Getting error codes on Oven can be quite difficult to find out what it really means and why they pop up. I took some time and searched your question in the Manage My Life website and found this great link on error code "F93". I attached the link below. Hope this helps!

Read More
Dezeray S -
November 16, 2010
A:

The F93 and F90 codes that you are seeing indicate that you have a failure in the oven door lock circuit. Diagnosing and repairing this type of failure is normally performed by a service technician. You may be able to SHUT OFF THE CIRCUIT BREAKER and access the control board and lock yourself. Pull the range out from inside the counter so that you can access the screw on each side of the console (see 2nd image below). With those screws removed, you should be able fold out the console. Carefully check the wiring. I provided a wiring diagram and the technical information on the door lock assembly in the first image below. If you find no problems with the wiring, you may be able to access and replace the door lock assembly. If you are not completely confident that you can safely complete this repair yourself, I recommend that you have a service technician fix the range. I provided a link for the Sears Service website below. If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
November 17, 2010
See more answers

Top Parts