Model #79046123300 KENMORE Slide-In Range, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore elite range (slide-in)

A:

I can definitely understand your concern over whether or not you can use a pressure cooker on your range. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
August 02, 2013
A:

Thank you for contacting ManageMyLife.com regarding using your pressure cooker on your Kenmore Elite slide in electric range. I understand your concern and I am happy to help you today.

If the owner's manual does not advise against the use of a pressure cooker, then you should be okay. Be sure that the pressure cooker conforms to the size of the burner that you are using. The burner will cycle off when the temperature of the glass reaches a certain point. This will normally protect the glass top from damage, but it can sometimes interfere with the cooking process. Please keep in mind that there is always a chance that it could crack/break the glass top. Do not slide the heavy pot across the glass top, pick it up and move it. Use utensils that have a flat clean bottom. Concave or convex bottoms will cause the element to cycle off and on and be very slow to heat.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

 

Read More
Korinna S -
Sears Technician
August 03, 2013
See more answers
Q:

keep getting f3 error code after changing temp probe.

A:

Appliance error codes can be confusing.  While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue.  I have added the link below. Hope this helps! 

Read More
Yadira B -
March 10, 2013
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is having trouble with your range displaying an error code. We are here to help. I suspect the new probe is bad. The information from the probe, goes directly to the control board. Yadira provided you a good link on testing the probe. I recommend that you use it. Just click here to view that link. If the new probe checks good, I recommend checking the wire from the probe hook up to the board with a multimeter. I hope this helps.
 
To order range parts, please visit SearsPartsDirect.com with the model number.
 
Please feel free to let me know if you need further assistance. We are always here to help.
 
Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
March 12, 2013
See more answers
Q:

can you provide installation instructions?

A:

I can understand your need for some type of instructions on how to replace the element on your range. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
February 04, 2013
A:

I posted a wiring diagram for that range in the image below. That information may help you wire up that bridge element. Be sure that you shut off the house circuit breakers for the range to completely disconnect electrical power before accessing internal components.

The original element may have had jumper wires that are no longer needed on the new element. The new element has some internal jumper contacts that are incorporated into the part.

If you are not able confident that you can properly connect the wires on that new element using the wiring diagram below, then I recommend that you have a service technician install that bridge element. You can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 05, 2013
A:

Here is the image.

Read More
Lyle W -
Sears Technician
February 05, 2013
See more answers

Top Parts