Model #79036673400 KENMORE Slide-In Range, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Problem with oven 790.36673400

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your range. Upon researching model790.36673400; the F31 error code indicates that there is a shorted temperature probe or bad probe wiring harness.  If the probe and harness are ok then the electronic control board may be at fault. I have posted a link of the electronic control board to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
July 19, 2015
Q:

Burners will not ignite 79036673400 Kenmore Gas range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the gas range.
 
Glad to help out.   Im  looking at your Kenmore range model number 79036673400.    

Sounds like your ignitors are bad.   They aren't getting enough power to stay on.   Below is a way to check them.

1.  Unplug the oven from the wall for your safety.
 
2.  Lower the oven door.  Sometimes best to have more room and just remove it.
 
3.  Remove the oven racks from inside.  Remove the lower panel when testing the bake ignitor.
 
4.  Remove the burner shield by taking out the screws that secure it to ignitor first.
 
5.  Next take out the screws that hold the ignitor.  Pull the ignitor away from the oven wall.
    Unclip the wire connector.  If the wire connector is not accessible, remove the back rear
    panel to the oven, or remove the bottom storage drawer to access the wire connector.
 
6.  Get a multimeter to the lowest setting so you can measure the Ohms of resistance.  Calibrate
    the meter. Refer to your meters instructions 
 
7.  Place one of the terminals on the ovens bake ignitor's terminal with one of the multimeters 
    probes.  Then touch the other terminal with the other probe.
 
8.  Check the multimeter's display  If the meter does not move, displaying a resistance of any 
    numbers on the Ohms of resistance, there is no continuity.   If no continuity then the bake 
    ignitor is bad.

 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 
 

Read More
Larry L -
Sears Technician
May 02, 2014
Q:

Broiler (only) not working

A:

I'm sorry to hear that you are having some difficulties with your Range. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Priscilla V -
October 31, 2011
A:

You could have a problem with the ignitor, the clock control board or the wiring in that circuit that could be causing this failure. The theory of operation for the ignition system on those oven burners is shown in the image below. If that broil ignitor is glowing when the oven is set in the broil mode then the clock control and the rest of the ignition circuit is okay. It is likely that you will need to replace the broil ignitor (part 18177710) in that situation. You can order that part from the Sears PartsDirect website. Here is a direct link for that part: Ignitor .

If that ignitor is not glowing, then you could have a failed ignitor, a bad clock control board or a wiring failure in that ignition circuit. There is a slight chance that you have a bad safety gas valve.

These tips may help you resolve the broiler problem in your range. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 01, 2011
See more answers

Top Parts