Model #79036603603 KENMORE ELITE Slide-In Range, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers


Oven door won't close 79036603603 Kenmore Elite Gas range


Thank you for contacting Sears. I will be more than happy to assist you with your Kenmore range.

I can understand the frustration of your range not functioning properly, after researching model number 790.36603603. there is a kit available to fix this problem. The kit has parts to replace the left and right side hinges and receptacles. Each kit contains 2 hinges and 2 receptacles. The Hinge Kit part number is 5304445529. Below I have linked the parts to our website at

Click here.

I hope you found this information useful. Again thank you for choosing Sears. We appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting*

Read More
Benny23 -
Sears Technician
July 07, 2015

Troubleshoot Oven Problem 79036603603 Kenmore Elite Gas range


Hello glad to help.  Thank You for choosing Sears
I am sorry and do understand your frustration when there is problems with the range.
Glad to help out.   Im  looking at your Kenmore gas range model number  79036603603.

First thing is you need to test the ignitors please.

How to test gas ignitors for ranges:
1.  Unplug the oven from the wall for your safety.
2.  Lower the oven door.  Sometimes best to have more room and just remove it.
3.  Remove the oven racks from inside.  Remove the lower panel when testing the bake ignitor.
4.  Remove the burner shield by taking out the screws that secure it to ignitor first.
5.  Next take out the screws that hold the ignitor.  Pull the ignitor away from the oven wall.
    Unclip the wire connector.  If the wire connector is not accessible, remove the back rear
    panel to the oven, or remove the bottom storage drawer to access the wire connector.
6.  Get a multimeter to the lowest setting so you can measure the Ohms of resistance.  Calibrate
    the meter. Refer to your meters instructions 
7.  Place one of the terminals on the ovens bake ignitor's terminal with one of the multimeters 
    probes.  Then touch the other terminal with the other probe.
8.  Check the multimeter's display  If the meter does not move, displaying a resistance of any 
    numbers on the Ohms of resistance, there is no continuity.   If no continuity then the bake 
    ignitor is bad.
NOTE: You should not perform this live voltage check unless you are completely confident in your technical ability to safely execute it. 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our

Read More
Larry L -
Sears Technician
July 11, 2014

How to put back oven door on Kenmore Elite?


I’m sorry; you forgot to provide us with the model number of your Kenmore oven. We need the model number in order to access the service & other related material. This information is usually available in the owner’s manual. Please resubmit with a complete valid model number for further assistance. I have also provided you with instructions covering this subject on one model of oven door.

Read More
biker dave -
Sears Technician
January 18, 2010

79036603603 kenmore customer has the same situation , she needs to know how to put door back on to the oven

Read More
kasandra -
October 18, 2013
See more answers

Top Parts