Model #79030473403 KENMORE Wall Oven, Gas

  • Control Panel
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Door/drawer
    3 Results
  • Wiring Diagram
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

F11 ERROR CODE ON MY GAS OVEN

A:

Error codes can be inconvenient and keep the appliance from working properly. Managemylife.com is a great place to find the answers to just about anything, especially on a range. I would suggest that you provide a little more information such as the make and complete model number of your product, so your expert will be able to provide you with the best possible answer. Just click on reply down below, where you can provide the additional information.

Read More
Joseph P. -
December 12, 2011
A:

I see Joseph provided you with good information on the F11 error code. These codes can be specific to certain models. For further assistance on your specific oven, please provide the complete model number and more detail. We will be delighted to assist you.

Read More
Korinna S -
Sears Technician
December 13, 2011
A:

I have a kenmore wall gas oven model790.30473403 giving an F11 code tried powering unit off to reset but no luck key pad unresponsive unit is beeping door is not locked

Read More
Robert -
March 09, 2013
A:

Any ideas on how to solve this or is sledgehammer in its near future?

Read More
Robert -
March 09, 2013
See more answers
Q:

Kenmore wall oven Model 790.30473403 will not heat.

A:

Ovens are just so handy and can be so disappointing when not properly working. I have found a page here on Manage My Life that may be able to assist you with your problem. I have attached the link below. Hope this helps.

Read More
Alina F. -
October 07, 2010
A:

Make sure that the gas cut-off valve for the oven is fully open and that you have an adequate gas supply provided to the oven.

The ignition system for this oven is shown in the image below. It is rare for the bake and broil burners to fail both at the same time. Since the bake burner is heating up to 200 degrees, I recommend that you pull the bottom oven panel and check that burner first. See if the igniter is glowing and whether the burner ignites properly. It likely will since the oven is heating up to 200 degrees in the bake mode. See if the burner cycles off and on fairly quickly. Check the flames according to the guidelines in the second image. Adjust the flames if necessary. If the flames are okay but the burner shuts off and appears to have a hard time reigniting then you could have a weak igniter. A technician will normally check the amp draw in the circuit using a clamp-on ammeter as shown in the third image. If the amp draw in the circuit is not reaching 3 amps then a weak igniter is preventing the safety gas valve from opening. Most people do not have a clamp-on ammeter and the cost of buying one for this single diagnosis does not make economic sense. You may need to have a service technician diagnose and repair your oven. Here is a link for the Sears Service website: Sears Home Services .

You can check the broil circuit in the same manner.

If the igniter is not glowing then you could have a problem with the electronic oven control board, the igniter or the safety gas valve. If you have a volt/ohm meter, you can check for continuity in the circuit. I provided a wiring diagram for the oven in the 4th image below. Shut off the house electrical breaker and shut off the gas supply to the oven before accessing internal components and checking continuity. If you need help with accessing the components, reply with additional details.

These tips may help you determine the cause of your oven problems. This failure can be complicated to diagnose. Reply with additional details if you need more help. If you are not completely confident that you can diagnose and repair the oven yourself, don't hesitate to call a technician.

Read More
Lyle W -
Sears Technician
October 08, 2010
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
October 08, 2010
See more answers

Top Parts