Model #7800231 SNAPPER Walk Behind Lawnmower, Gas

  • Handles/controls
    3 Results
  • Deck
    3 Results
  • Engine & Blade
    3 Results
  • Front & Rear Wheels
    3 Results
  • Transmission (21")
    3 Results
  • Decals
    3 Results
  • Wiring Schematic
    3 Results
  • Handles/controls
    3 Results
  • Deck
    3 Results
  • Engine & Blade
    3 Results
  • Front And Rear Wheels
    3 Results
  • Transmission
    3 Results
  • Decals (21")
    3 Results
  • Wiring Schematic
    3 Results
Find part by diagram >

Question and Answers

Q:

Snapper mower won't start 7800231 Snapper Mower

A:

I'm sorry to hear about the difficulties with your Snapper mower. I did some research at Managemylife website and found this expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. One other thing I would check is the gas cap. It can cause this issue too. I hope this helps you until your expert responds.

Read More
James -
August 02, 2013
A:

 Thank you for your question. Usually when the mower starts and stalls, right away it has a dirty carburetor. First, make sure the fuel is no older than 5 weeks old. Next check the air filter. If the air filter is plugged the mower may not run. If the air filter is clean and the fuel is fresh, I recommend cleaning the carburetor.  To clean the carburetor you have to remove the spark plug wire and tip the mower on to its side. Make sure the oil fill tube is towards the ground. Then remove the float bowl nut on the bottom of the carburetor. Some fuel will leak out so do this in a well-ventilated area. Remove the float bowl, clean it with carburetor cleaner, and dry it. Do not get carburetor cleaner on the rubber gasket. The cleaner will expand the rubber and renders it useless. Next, put the straw on the spray nozzle of the carburetor cleaner. Spray the cleaner in to the holes where the float bowl nut came from. These are the fuel pick up tubes. Once those are flushed, clean the holes on the float bowl nut. I recommend cleaning the holes with bread tie wire and carburetor cleaner. Then assemble the carburetor.  Tip the mower back up right and test the operation. If the engine does the same starting and stalling, I recommend replacing the carburetor.  I had a customer send me a link to video he found that shows how to clean the carburetor. The engine is not exactly the same as yours but it will give you a general idea. Here is a link to that video   I hope this is helpful.  If you need further assistance, please reply with more details and a model number.          If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a  Sears technician.  Here is a link for the website: Sears Home Services .  Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
August 02, 2013
See more answers
Q:

Snapper walk behind mower fires up then quits 7800231 Snapper Mower

A:

I'm sorry to hear about the difficulties with your Snapper mower. I did some research at Managemylife website and found this expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. One other thing I would check is the gas cap. It can cause this issue too. I hope this helps you until your expert responds.

Read More
James -
August 02, 2013
A:

 Thank you for your question. Usually when the mower starts and stalls, right away it has a dirty carburetor. First, make sure the fuel is no older than 5 weeks old. Next check the air filter. If the air filter is plugged the mower may not run. If the air filter is clean and the fuel is fresh, I recommend cleaning the carburetor.  To clean the carburetor you have to remove the spark plug wire and tip the mower on to its side. Make sure the oil fill tube is towards the ground. Then remove the float bowl nut on the bottom of the carburetor. Some fuel will leak out so do this in a well-ventilated area. Remove the float bowl, clean it with carburetor cleaner, and dry it. Do not get carburetor cleaner on the rubber gasket. The cleaner will expand the rubber and renders it useless. Next, put the straw on the spray nozzle of the carburetor cleaner. Spray the cleaner in to the holes where the float bowl nut came from. These are the fuel pick up tubes. Once those are flushed, clean the holes on the float bowl nut. I recommend cleaning the holes with bread tie wire and carburetor cleaner. Then assemble the carburetor.  Tip the mower back up right and test the operation. If the engine does the same starting and stalling, I recommend replacing the carburetor.  I had a customer send me a link to video he found that shows how to clean the carburetor. The engine is not exactly the same as yours but it will give you a general idea. Here is a link to that video    I hope this is helpful.  If you need further assistance, please reply with more details and a model number.         If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a  Sears technician.  Here is a link for the website: Sears Home Services .  Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
August 02, 2013
See more answers