Model #7602 WEBER Grill, Gas

  • Platinum Series Ii Side Burner
    3 Results
Find part by diagram >

Question and Answers

Q:

just need to know possible parts 7602

A:

I am convinced that you will be able to do this job yourself. By doing it yourself, you get paid by not spending. Do you have an idea of what part may be the issue (i.e. igniter). I have provided a link below that will pull up a full page of gas dryers that don't heat issues. Review 5 or 6 of these and you will begin to gain a theory you can work from. The second link below will be for Sears Parts Direct.com. I entered the model number you provided and did not get a response. Try to find and send us the full model number. You will hear from an expert within two days if not sooner. I hope this helps and have a nice morning.

Read More
Henry -
November 05, 2012
A:

Thank you for submitting your question. If the gas dryer is not heating, you could be experiencing an issue with the burner assembly which consist of the igniter and gas coil valves. You could have an issue with the two thermostats, thermal fuse, or thermal cut-off. These parts would need to be tested with an ohms/volt meter to determine the failure. The 7602 is not the complete model number. You're model number should start with the prefix of 110, 417, 796, or 402. This number will be followed by a period and 6-8 other numbers. The model number should be located on the interior door or along the opening frame. For further assistance with this repair, please reply back to this thread with the complete model number of your dryer. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
November 05, 2012
A:

henry & tykara thanks for, what, were you trying to confuse me or are u on the sales team? ex,*ie igniter really? is that where u would start?good thing you think you dont have 2 do this 4 yourself.how bout u start w the (ie igniter. actually that was my first guess, mecanichally common sense prevails .thermocoupler,etc but burner assy coils etc.if u r trying 2 help start w the easy answer we'll check back

Read More
kevin -
November 07, 2012
A:

Kevin, you asked what parts to look into and I've provided that information. If the unit is running but not heating those would be the parts to check. Otherwise, you'd be ordering parts blindly and may not get the correct one to solve your issue. The thermal fuse and the thermostats are the easiest to access. With the ohms meter you'll want to get a reading of zero for each of them. If you see that the igniter is cutting on and off then that would be an issue with the coil valves. All these parts aide your dryer in heating. You can't know which part is in need of replacement without testing first. If you'd like further assistance with this repair, please reply back with the complete model number. Otherwise, you can schedule for service through the link provided below.

Read More
Tykara -
Sears Technician
November 07, 2012
See more answers
Q:

top load washer

A:

It's always important to have proper instructions to replace a part on a washer. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
August 07, 2012
A:

That link for a previous answer that Julio posted in the above response should help you replace the suspension rod in that washer. Be sure that you tape the lid shut before lifting that top panel. Also, be sure that you unplug the washer before beginning that repair.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
August 09, 2012
See more answers