Model #7580 FUNAI VCR

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Model 110 load not complete Kenmore Model 11026002010

A:

Mine started doing the same thing but eventually it would start the drain and spin cycle but it was very noisy when it was spinning, but not like it was unbalanced or anything, Did you find this to be your problem and if so what was the end result.

Read More
Abby -
April 15, 2014
A:

Mine started doing the same thing but eventually it would start the drain and spin cycle but it was very noisy when it was spinning, but not like it was unbalanced or anything, Did you find this to be your problem and if so what was the end result.

Read More
Abby -
April 15, 2014
A:

Mine started doing the same thing but eventually it would start the drain and spin cycle but it was very noisy when it was spinning, but not like it was unbalanced or anything, Did you find this to be your problem and if so what was the end result.

Read More
Abby -
April 15, 2014
A:

Mine started doing the same thing but eventually it would start the drain and spin cycle but it was very noisy when it was spinning, but not like it was unbalanced or anything, Did you find this to be your problem and if so what was the end result.

Read More
Abby -
April 15, 2014
A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
A:

This site sux. No one ever answers these questions. Don't you have a tech that can help or is it just about making money?

Read More
Nan -
May 16, 2014
A:

Mine won't spin at all. any suggestions on what part to replace?

Read More
jeff -
June 04, 2014
A:

I do apologize you feel that way. We provide free Technical information to our customers. Our service -technician runs around 75-80$. 


If your unit is not spinning I would check the belt to see if the belt is broke. The belt will go first when the unit will not spin. 

If you have any other questions. Please resubmit your question. Thank you.

Read More
Natasha12 -
Sears Technician
June 05, 2014
See more answers
Q:

GE dryer model no. DDG7580B DDG7580B

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Henry -
July 26, 2013
A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when having dryer problems.   Will be glad to confirm the belt information.

Yes, the we12x0082 is the correct belt for this model DDG7580B.  You sound like you know what you are doing on changing the belt.   I am sending you information on how to change that belt so may help in checking to see if all is well.

Instructions on changing a GE dryer  belt:

1.  Unplug the dryer and open the dryer door.

2.  Unscrew the screws under the top lip, where the dryer's door closes, with your screwdriver. Once these screws are removed, lift the top off of the dryer. On older models, the entire top will hinge upward out of the way, and on models made after 1997, half the top will pull off.

3.  Remove the screws on the inside-top corners of the front panel so the front panel of the dryer can be removed and set aside. On models made before 1997, the front panel should be carefully set to the right side; on newer models, the panel should be set to the left side of the machine. Be careful not to damage the door-control wires.

4.  Locate two screws approximately 6 inches off the floor on each side and remove them, allowing you to push the sides of the dryer slightly apart so the drum can be removed. Pull the drum slightly toward you and reach around to remove the dryer belt from the motor pulley. If the belt is broken, this step should not be necessary. Once the belt has been removed from the motor pulley, the drum should pull up slightly and out of the dryer toward you.

5.  Remove the old dryer belt and put the new one in place, with the ribs of the belt facing the drum. The slack part of the belt should be placed near the motor. Reverse the previous directions to replace the drum, replace the screws that hold the sides in place, replace the front and replace the top.

6.  Pull the dryer out from the wall and remove the four screws holding in the panel near the bottom of the back of the dryer. You will see the motor, the drum and the belt you just set in place. Loop the belt around the motor pulley and the idler pulley, and turn the drum by hand to make sure that the belt is straight and will stay in place. Screw the panel back on and push the dryer back into place against the wall.

Good luck, hope this helps.  If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

 

Read More
Larry L -
Sears Technician
July 26, 2013
See more answers
Q:

Craftsman motor

A:

I can definitely understand your need for some type of wiring diagram for your table saw motor. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
June 18, 2013
A:

Thank you

Read More
Edwin -
June 18, 2013
A:

Thank you for your question.  I will be happy to assist you. I looked up the model number you submitted. I could not get the model number to come up for me. I will try to assist you without it. Most of our old motors were wired the same. I emailed you a file that shows the wiring on many different motors. Open the file and see if any match your motor. If you find one that matched, follow the wiring instructions. If none of them match, please reply below with any other numbers you can find on the motor or saw. An image of the motor and motor connections might also be helpful.     Thank you for using Manage my life. Mark T.   

Read More
Mark T -
Sears Technician
June 20, 2013
See more answers