Model #7550 FUNAI VCR

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

No power to any outlets, no electricity, no Juice 01925 Troybilt Generator

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your generator. Upon researching model number 01925; each part would have to be tested for power. Try to see if power is being made from the alternator. Follow the power from the alternator and try to find where it stops.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
July 09, 2015
Q:

Unlock the oven

A:

If anyone can get the Maytag oven unlocked after a clean cycle, our experts can. I am providing a link to the owners manual and there is information on page 9 and 17 that may be helpful. Additional information may take 24-48 hours. If you decide on service, that link is also available.

Read More
Anna T -
January 13, 2013
A:

Thank you for your question and I understand your concern.

After the oven has cooled down from the clean cycle, the "LOCK" light will turn off at which time you should be able to open the oven door. If the "LOCK" light is off and door will not open, it could have a faulty door lock assembly or electronic oven control. You may be able to remove the rear panel from behind the range and access part of the door locking mechanism. You may be able to manually slide or push and pull the mechanism to unlock the door. Disconnect the power cord from the power source before removing the rear panel.

The electronic oven control will generally display a fault code if there are any failures.

It could also be in a control or oven door lock mode too.

Locking the Control and Oven Door:

The touchpad controls and oven door can be locked for safety, cleaning, or to prevent unwanted use. They will not function when locked. If the oven is currently in use, the controls and door cannot be locked. The current time of day will remain in the display when the controls are locked.

  • To Lock:

Press and hold the CANCEL and Cook & Hold pads for three seconds, (Press CANCEL pad first) LOCK flashes in the display,

  • To unlock:

Press and hold the CANCEL and Cook & Hold pads for three seconds. (Press CANCEL pad first.)

LOCK disappears from the display.

If this is not the case, I strongly suggest calling a service technician to diagnose and repair your range.

You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 15, 2013
See more answers
Q:

How do I rebuild the clutch on my truck???

A:

When making some major adjustments on a vehicle, Manage My Life is here to help. While you are waiting for your expert answer, I did manage to find a link that will provide you with some good information to help you with your question. I hope my link is useful.

Read More
Joseph P. -
July 30, 2011
A:

thank you for the link....info is too general to be of any help

Read More
Eric2010 -
August 02, 2011
A:

Removal

Disconnect the battery negative cable. Remove clutch slave cylinder, or the hydraulic line quick disconnect using quick disconnect tool T88T-70522-A. Remove the release lever if so equipped. Remove the dust cover it so equipped. Remove transmission. Mark the assembled position of the pressure plate and cover to the flywheel (for re-assembly). Remove the pressure plate and cover assembly and the clutch disc from the flywheel. Installation

Position the clutch disc on the flywheel so that the Clutch Alignment Shaft D79T-7550-A or equivalent can enter the clutch pilot bearing and align the disc. When re-installing the original pressure plate and cover assembly, align the assembly and flywheel according to the marks made during the removal operations. Position the pressure plate and cover assembly on the flywheel, align the pressure plate and disc, and install the retaining bolts that fasten the assembly to the flywheel. Tighten the bolts to specification and remove the clutch disc pilot tool. Clean and lubricate the release lever pivot stud. Reinstall the transmission. Correctly position the release lever (if so equipped) in its release bearing hub, and align with the pivot stud. Push inward on the lever until it snaps into position. Reinstall the external slave cylinder, or attach the hydraulic tube quick connect fitting. Install the dust boot if so equipped. Install the starter motor.

Read More
MikeLangton -
Sears Technician
August 04, 2011
See more answers