Model #7334 PORTER CABLE Sander

  • Sander
    3 Results
Find part by diagram >

Question and Answers

Q:

Gas dryer, maytag model # LDG7334AAE not heating/drying clothes well.

A:

It can be a real headache when your dryer fails to heat properly. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
February 21, 2013
A:

Hello Shelly,

 

I'm sorry to hear that your dryer is not working correctly and I would like to assist you.  A common cause of incorrect combustion is a dryer vent that is partially plugged.  I think that it would be a good idea to turn the dryer on a no heat or low heat setting and then go to where the vent exits and check the exhausting air flow.  It should be quite a bit, about the same amount as a hair dryer, just not moving quite so fast.  If it is plugged or you see a lot of lint and debris, be sure to turn the dryer off and then clean out or have a vent company clean out the vent and then test your dryer again.  If the air flow seems OK, and since there is likely an issue with incomplete combustion, this may be a safety issue and I am advising you to call an experienced technician or follow this link: Sears Home Services to arrange an appointment with a Sears Technician. 

 

Please let me know if you would like any further assistance.

 

Jerry C

Read More
Jerry C -
Sears Technician
February 22, 2013
See more answers
Q:

Awful Noise LDE7334ACM Maytag Maytag laundry

A:

It is hard to concentrate when there is a noisy dryer going in the background. While waiting for an expert response on your specific model and concerns, please check out the link provided below. Thanks for your patience.

Read More
Anna T -
February 17, 2013
A:

Thank You for Submitting your question to ManageMyLife.com

I can understand your frustration with having your dryer making this horrible noise.

Could you please explain the noise to me? Squeaking? Banging? Grinding? Etc.

Read More
Desirea -
Sears Technician
February 17, 2013
See more answers
Q:

Maytag Gas Dryer Pilot

A:

I can understand the frustration when something like this happens after a repair. It doesn't seem to make sense. The expert will review and respond but if checking an enlarged image of the dryer parts diagram would help, I attached the link below. I hope this helps.

Read More
Barbara H. -
February 11, 2012
A:

I'm not sure I completely understand the problem. This unit has a glow bar ignitor and doesn't use a pilot flame. The ignitor should glow with extreme brightness when it is working to lite the flame when the gas valve releases the gas.

Having the front panel in place should not prevent the ignitor from glowing.

The hi-limit thermostat and radiant sensor will prevent the ignitor from glowing if they are bad.

Please reply with some additional details for further assistance with this problem.

Read More
Fred M -
Sears Technician
February 11, 2012
A:

Hi, I think I meant ignitor, not pilot. Before I replaced the gas valve solenoid and cycling thermostat, the ignitor did not glow. After I replaced them, the ignitor glowed if the front panel is out. When I put back the front panel, the ignitor stops glowing. I thought there is air coming out of the vent hood that makes the ignitor stop glowing.

Read More
magda -
February 12, 2012
A:

Magda you certainly have an unusual problem. If replacing the cycling thermostat caused the ignitor to glow then that was likely the problem. The front panel should have nothing to do with the ignitor glowing or not glowing as long as the motor is running. Putting the front panel inplace should not cause the ignitor to stop working. The ignitor must glow and then the radiant sensor should click and shut the ignitor off and open the valve. With caution you can run the dryer with the front panel off if the door switch is not disconnected. Unplug the dryer first while removing the front panel. Let me know how it goes.

Read More
Fred M -
Sears Technician
February 13, 2012
See more answers