Model #7330 KENMORE Air Cleaner

  • Functional Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

My Jeen air hood does not work properly. I need schematic & wiring diagram to circuit board on Jenn Air Kitchen hood model # JXT583

A:

I did some research on the range hood and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within two business days with detailed information. Thank you for using Manage My Life.

Read More
Joseph P. -
May 18, 2013
A:

Thank you for your question. I'm attaching the wiring diagram below for this range hood. I hope this will help you.

Read More
Scott D -
Sears Technician
May 21, 2013
A:

Thank you very much Scott D. My circuit is a little different than the diagram you sent me. I have numbers from the left : 6-5-4-3- the number 6 on my board is not in your diagram. So I wonder what goes there. The wires named RED BLUE WHITE BLACK are the ones I have too. The question is: does RED goes to 6 or to M Then I have M and L1A-L2A and L1B-L2B at the same place of your diagram

Read More
Frank -
May 21, 2013
A:

Scott D, here are pictures of my board. someone else wrote on it and I am not sure how reliable that person is. So please tell me what goes where. Thanks.

Read More
Frank -
May 21, 2013
A:

Frank, the model listed is not complete and shows several models. I checked some of the models and they show the same diagram. Now, still having the M terminal, the diagram shows the red wire attached to it. The # 6 terminal will probably be for a different model. It's very common now for control boards to have extra terminals, which allows the same board to be used for different models with different features. If you would like more assistance, please include the complete model number. I hope this will help you.

Read More
Scott D -
Sears Technician
May 22, 2013
A:

I think its JXT583 ADS. I can not find a circuit board like this anywhere. So I looked at it and saw that the transformer looks burned. and its very hot when its plugged in. The transformer info are: TYP 30/18 04/06 T BV 030-7330.0 PRI 115V 50/60 HZ I think I need a new board but it is obsolete. They have a new one (very expensive) but it may not work. Do you have any idea where I can get this transformer or a used circuit board?

Read More
Frank -
May 22, 2013
A:

Frank, unfortunately parts on control boards are not sold separately. Now, circuit boards may be rebuilt sometimes but not very often. Trying to find a used board that would sub for this board, probably does not exist. This will most likely not be repairable. I hope this will help you.

Read More
Scott D -
Sears Technician
May 23, 2013
A:

Thank you Scott. Have a great memorial weekend.

Read More
Frank -
May 23, 2013
A:

Frank, thank you for using Manage My Life.

Read More
Scott D -
Sears Technician
May 24, 2013
See more answers
Q:

Model no 795.7330 bottom freezer drawer is stuck closed.

A:

I understand that your bottom freezer drawer is stuck closed. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
April 27, 2013
A:

I can see how upsetting this stuck freezer door would become.  These drawers do sometimes freeze shut, but I see you have eliminated that cause. Sometimes the door can get out of alignment and not sit correctly. Open the freezer door and located the door connectors (the large metal pieces that attach to the door about mid-way from top.) There are screws that hold these connectors to the door frame. Loosen the screws (do not remove) on both sides. Pull the door open and push the door closed hard. Check the seals, if not sealing repeat. Once you see the seal is good all the way around, gently open the door and tighten the screws.If the gasket has a winkle or fold in it, you can use gentle heat with a hair dryer to help soften and correct.  Another thing that sometimes happens when the drawer is removed for cleaning, is that it is not installed back correctly.  The installation manual can help confirm, but I was not able to locate information with the model number provided.  If further help is needed, please reply with the full model number.  Thank you for using Manage My life.

Read More
Barbara H. -
Sears Technician
April 28, 2013
See more answers