Model #7107 PRO-TECH Miter Saw

  • Base Assembly
    3 Results
  • Motor/guard Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

schematic ice bin in our Kenmore Elite - part no. 5075JA1044E 795.7107

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

I have attached the information you need to put your ice bin back together. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

 

SAFETY NOTICE: Be sure to disconnect power to the unit before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
August 12, 2015
A:
Natasha12 -
Sears Technician
August 12, 2015
See more answers
Q:

Icemaker won't drop ice

A:

It is that time of the year to have ice for those cold drinks and I know you want to get this ice maker fixed as soon as possible. I am providing a link on a similar issue which may be helpful while you receive model number specific information.

Read More
anna -
June 07, 2013
A:

I know that it can be very frustrating to have issues with your ice maker. The ice maker may not be harvesting the ice for a couple of reasons.

  • If the thermostat in the ice maker is not sensing the temperature properly. This thermostat senses the ice maker mold temperature and will start a cycle when the mold reaches a certain temperature.
  • The temperature in the freezer may not be cold enough (below 10 degrees). If the temperature never gets below 10 degrees it's a good chance that at times the temperature is getting even higher. If this is the case the average temperature might be closer to 15 degrees. In this case the ice maker mold will probably not get cold enough for the thermostat to start a cycle.

I would suggest checking the freezer temperature. If it's not getting cold enough turn it up. A good check would be to place a thermometer between two frozen packages of meat and read the temperature that way. If the temperature is correct, then I would suggest testing the ice maker. The image below will provide the testing information for you. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 07, 2013
A:

Thank you for your reply. I tested the icemaker by holding the cube size button for 3 seconds as advised elsewhere. The icemaker dropped ice and refilled properly. Note: this icemaker is in the door. The freezer compartment, located in a bottom drawer, has seemed warmer than usual lately. I change the setting from 0 to -6 and it seemed even warmer. I moved it back to 0 and it cooled some but still not cold; no ice.

Read More
Terry -
June 10, 2013
A:

It does sound like there may be an issue with the freezer temperature. I would suggest you try decreasing the temperature again, please remember that it takes a full 24 hours for the unit to cool completely. If this does not work, check for a frost buildup on the back of the unit. If there a lot of buildup, the freezer can not cool. If this is the case try manually defrost the refrigerator and then see if it works.

Read More
AnneJ -
Sears Technician
June 10, 2013
A:

I left the -6 setting for more than 24 hours. When I first noticed a problem I pulled the refrigerator out and opened the back cover to clear dust etc. but the compartment was clean and free of icing.

Read More
Terry -
June 10, 2013
A:

Terry, is the ice in the tray frozen? If so there is a test that you do on the ice maker to see if this is the problem. The image below will show you how to do this. If the ice drops and then cycles, the ice maker needs to be replaced. If the ice is not frozen the you are looking at a problem with the freezer. This could be happening becuase of the temperture sensor, the contorl board, or the sealed system. Testing these parts however is something you want a technician to do becuase they are very complicated. If you would jsut like for a tech to come out and diagnose this, just click on the link below. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 11, 2013
A:

Yes, the ice is frozen and does drop when a cycle is forced. Another link on this website said this indicated that the icemaker did not need replaced; but that the problem was elsewhere in the appliance.

Read More
Terry -
June 11, 2013
A:

I did some further research on this model, and found that you could be having a problem with either the control or the sensor. Try to reset the ice maker by turning it off for a few minutes and then turning it back on. If that does not help, try to reset the main control board in the refrigerator by unplugging the entire refrigerator for 5 minutes. Plug it back in and see if the ice maker starts working properly. If resetting the control boards in this manner does not help, then you can try to run the ice maker through a test function using the information shown in the image below. If the ice maker will not cycle properly, then it will need to be replaced. Please let me know if you need anything else. Thank you fo using Manage My Life.

Read More
AnneJ -
Sears Technician
June 12, 2013
A:

AnneJ, I have a Kenmore Elite bottom freezer refrigerator Model #795.7107. It stopped dropping the ice cubes. When I shut the ice maker off and then turn it back on it tries to rotate the Ice tray but it makes a loud clicking noise then stops. IF I put my fingers in above the guard I can feel the frozen cubes. I felt around and it does not feel like anything is stuck but that is what it acts like. In this thread you included a couple of attachments but they are only the size of a postage stamp when I try to open them. One was for testing the ice maker the other is to reset the control boards. Can you please send them to me or tell me how to open them correctly. I would like to try it before calling for a repair. Thank you

Read More
SALLY -
July 13, 2015
A:

I too would like to receive those documents in a readable format. I'm surprised this information isn't included in the user manual.

Read More
Valerie -
August 04, 2015
See more answers
Q:

Fridge is at 50 degrees�?�no fan sounds? Freezer is working fine. Vent and flow pattern clear. Ideas? 795.7107

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

The thing to check would be the air diffuser that helps the air travel from the freezer to the fridge. Some times when the diffuser closes the cold air from the freezer could freeze it closed. The diffuser is accusable from inside the fridge section. It’s the opening in the top left corner of the fridge. 

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.
 

Read More
JeffwallaceIII -
Sears Technician
July 27, 2015
A:

The top left corner of my fridge is only home to the water filter. Can you reference manual 1006610L page 8? We did empty and unplug the unit for two hours. After we plugged it back in, the freezer is again working fine, but the top fridge portion cannot cool below 50 degrees. Since there is only one compressor and we can hear a fan, we are assuming it�??s a thermostat, but now you have me curious. The bottom-most freezer drawer had a lot of ice build up for some reason. This unit was purchased in January of 2013 and we spent a small fortune. I AM VERY UNHAPPY. The older Sears model we inherited with the home we purchased when we moved down here is still A-OK in our garage. It�??s from 1999. If I had known Kenmore Elite products were made by LG now too, I would have never purchased it. I really hope it�??s something minor.

Read More
CORINNE -
July 27, 2015
See more answers