Model #707 CURTIS MATHES Misc Audio

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

runs rough SV7350016 Kohler Engine

A:

Thanks for the inquiry and for being a valued member.

You are probably right, the ignition module on the right side is sporadic and is not consistently generating spark, and you're only running on one cylinder. Kohler has discontinued the older style of ignition for a newer updated MDI system. This new MDI no longer requires 12 volts to function. 

The kit needed for this SV735 series Kohler engine is part number 32-707-01-S. It will include both modules, and everything needed to make the conversion. It should also include installation or conversion instructions. 

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
August 17, 2015
A:

I had the same problem with my 917.287462 mower. Ordered the 32-707-01-S kit, installed it, and the mower started but then died after about 10 seconds. I tried it a second time with the same results, now the mower won't start at all. I double checked everything to make sure that I installed the kit correctly. Appreciate any advice/help.

Read More
BeeCrazy68 -
August 26, 2015
A:

I have a 917.287462 with a Kohler engine SV735. I need to clean the carburetor but I can't get the air cleaner base off, how and or what size wrench fits the screws?

Read More
Michael -
November 04, 2015
See more answers
Q:

Replacing water line in my Kenmore Elite Bottom Freezer Refrigerator

A:

Thanks for the information about your refrigerator model 79577242600; sorry you have a problem, I will be glad to assist you.  All the tubing on the back of the refrigerator can be ordered and replaced and the tubing comes with the correct connectors. (When ordered correctly through our parts department)  If the tubing inside the cabinet has been damaged it is not replaceable.  Here is a link to Sears Parts Direct and you model parts description. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.Ron H.

Read More
Ron H -
Sears Technician
November 21, 2013
A:

Ron, I ordered the replacement tubing. The original connector located on the end of the damaged white flex water supply line that connects to the water supply line from the house is intact. I didn't order a replacement connector. You mentioned that the "tubing inside the cabinet" is not replaceable. Are you referring to the the tubing internal to the refrigerator? You mentioned that all of the tubing on the back of the refrigerator can be ordered and replaced. I'm confused, because the white flexible tubing on the back of the refrigerator enters into the inside of the refrigerator. I am hoping that I can replace the white flexible tubing on the back. I do not know what to do about the fact that the top end of the tubing enters the refrigerator at the top and disappears into foam insulation. Can you please clarify?

Read More
Stephen -
November 21, 2013
A:

Hi Steven, the ice maker fill tube that goes inside to the ice maker can be changed as well as the tubing on the outside. Any tubing that runs through the cabinet (inside liner like the water for the door can't be changed, but external tubing can be changed. The parts page I sent shows the fill tube for ice maker if you need it; it is separate from the actual tubing leading to it. I hope this help clarify. Ron H.

Read More
Ron H -
Sears Technician
November 23, 2013
A:

How do I physically remove the tubing end that disappears into the back of the refrigerator at the top left behind the plastic cover held on by 2 screws and disappears into foam?

Read More
Stephen -
November 23, 2013
A:

Hi Steven, I suppose that now I am the one confused, I indicated that tubing that is inside the liner cannot be replaced, if you could send me another picture, this time of the tubing where it enters the unit after you have removed the screws and the plastic cover perhaps I will better understand. Sorry for the confusion, if I can see it I should be able to better help you. If I need to I will contact my represenitives for this product. Ron H.

Read More
Ron H -
Sears Technician
November 23, 2013
A:

I have attached 3 images. Where the tubing enters into the back of the refrigerator, a view farther out and finally one of the back of the refrigerator. As you can see, the white tubing that I want to replace is located on the upper left corner of the refrigerator. The hole where it enters the back of the refrigerator is covered with a plastic cover held in place with 2 metal screws (removed). Refrigerator MFG date 07/2007, Model #: 795.77253601, Serial #: 707MRKU04149.

Read More
Stephen -
November 24, 2013
A:

Ron, I've uploaded 3 more images. The first has an arrow showing the white flex tubing at the point where it enters the refrigerator in the back. The second is a photo of the replacement tubing and the original connector and finally a picture of the info tag for the refrigerator. I would appreciate knowing how to replace the white flex line. But as you can see it goes into the back of the refrigerator to where I have no idea. Can I reuse the old metal connector on the other end? Is this a job a mechanically inclined person can do?

Read More
Stephen -
November 24, 2013
A:

Thanks Stephen, for the images they are very helpful. That white line goes into the filter housing inside the refrigerator and can be replaced by removing the filter housing to access the fittings. The blue line is the return that goes to dispenser. If I may suggest, splicing the white tubing on the back of the refrigerator instead of pulling the housing (unless it is leaking up near where it enters the unit.) You can actually find fittings at most hardware stores, just take a section for sizing. (Most are 5/16th white). I would not recommend reusing the old connectors, these parts are very inexpensive and you don�t want to chance another leak. Thanks again for the images, and I hope this helps you complete your project. Ron H.

Read More
Ron H -
Sears Technician
November 25, 2013
A:

Ron, I got into trouble going to my local hardware store and splicing the line. When the white flexible tubing is stretched a little as over a barb for the splice, it splits. This is what happened to me originally. I think that's why the connectors at the ends are made the way they are, they don't stretch the tubing for seal. Is it hard to remove the filter housing? Do you have any instructions or know where I can get them? Thanks.

Read More
Stephen -
November 25, 2013
A:

Stephen, I do not have any instructions for removing the filter housing, however if you drop the filter you can see a screw on the top cover, remove it, once you have it off you should see one or more screws that hold the actual housing in place, remove them and pull it out. This is the most common method for your model; there are a few different depending on housing vendor all of which can be removed by removing screws that can easily be seen. Remember you will need slack in the water lines on the back side. None of the service manuals reference this job that I can copy you on. If you check you tube there may be videos on this subject. Ron H.

Read More
Ron H -
Sears Technician
November 25, 2013
See more answers
Q:

lawn tractor charging voltage

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina -
December 28, 2012
A:

Thank you for your question.



I will be happy to assist you. I looked up the model number you submitted. According to the parts list this model has a fuel solenoid installed on the bottom of the carburetor. The engine has the highest unregulated charging system on it. I checked in the manual for voltage output. It only gives the minimum output. 15.9 volts should be ok. I know my battery charger charges at 17 volts and I have never had a problem with any of my batteries.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life. Mark

Read More
Mark T -
Sears Technician
December 29, 2012
A:

Thanks for the help. Do I understand correctly that there is no regulator on the charging system?

Read More
Ken -
January 08, 2013
A:

Ken, That is correct. The engine does not have a regulator.

Read More
Mark T -
Sears Technician
January 14, 2013
A:

Perhaps I'm over thinking the set up in the wiring and charging system on this particular tractor. I have a similar situation with a tractor I own. My charging system is charging at 16.2 volts but it just seems high to me. I have putzed with tractors off and on and they all seemed to have some sort of regulator or resistor in the mix somewhere. I would really appreciate it if you would be able to shed some light on this for me. My tractor also doesn't have a regulator, where you think it would anyway. My tractor is a (under the seat) 247.289010 and (motor) 31c707 1347 B2. Is the 16.2 volts in a safe range? I just want to make sure because I would hate to cook anything. Its a great running tractor otherwise. Thanks a million for your time.

Read More
Thomas -
September 16, 2015
See more answers