Model #70 HOOVER Vacuum, Upright

  • Agitator
    3 Results
  • Cleaningtools
    3 Results
  • Handle
    3 Results
  • Hose
    3 Results
  • Mainbody
    3 Results
  • Motor Assembly, Hood
    3 Results
  • Outerbag
    3 Results
Find part by diagram >

Question and Answers

Q:

Q:

panel display on Kenmore Elite refrigerator

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
December 02, 2011
A:

Thank you for your question. I can understand your concern. This type of problem will usually be caused from a defective main board. The main board controls the functions of the display board. When you reset the board by disconnecting the power and then reconnecting it and it corrected the problem for awhile, it further indicates the main board # 6871JB1280P has failed. It's available at SearsPartsDirect . I hope this will help you. If you would like more assistance, reply to this thread and I will assist you further.

Read More
Scott D -
Sears Technician
December 05, 2011
A:

Thanks Scott. I suspected that, but the front panel is obviously easier to get to and check. Can I test any part of this board for continuity to determine FOR SURE that this part is working properly so I don't order and install the wrong part? Thanks! Oh, also, can you tell me the current part number for this display control board if I were to need a new one?

Read More
dave -
December 05, 2011
A:

I'm attaching the wiring diagram for the dispenser board to the main board on connection # 5. The main thing to check will be to see if, there are any loose wire connections at the boards and also the connection at the door hinge. If these connections and wires seem ok, the most likely problem will be with the main board. The dispenser board is # 3211JJ2001B. It will be an assembly. I hope this will help you.

Read More
Scott D -
Sears Technician
December 06, 2011
A:

Thanks again. It still bothers me that I have power clearly to this board when connected, which makes me suspect this board is the issue, although I have found continuity in all locations seemingly when I try to test it without being connected. My concern is that I am not properly testing the panel display and control board to know for sure. I guess I will just have to buy the new main board and see what happens and hope that is the problem. I just hate to take a $70 or $80 gamble - times are tight! :-) thanks so much for your help, I do really appreciate it.

Read More
dave -
December 06, 2011
A:

I understand what you mean. Unfortunately, this is all the wiring and electrical information available for the dispenser. However, if all the wires and connections seem ok and if you are getting continuity readings, it would be very unusual for this to be a defective interface board. This problem is almost always caused by a defective main board. If you would like more assistance please let me know.

Read More
Scott D -
Sears Technician
December 07, 2011
A:

Scott I have the same issue as described above on slightly different model refrigerator (795.75542401) The only thing I can add is then when I unplug the refrigerator and plug it back in the display and the buttons work for maybe be 30 -45 seconds and then is not responsive. I thought that it might be the main board or the dispensor board. I ordered and replaced both and the problem has not been fixed. Any idea where to go from here? The refrigerator itself seems to be working fine, but I cannot change temperatures on either the refrigerator or freezer and it no longer indicates when the door is open, which was really helpful with kids in the house...:)

Read More
Sharon -
January 04, 2012
A:

Sharon, Normally this would be defective main board problem, especially if it resets itself when the power is disconnected and then reconnected. However, since both boards have been replaced, with the same results, check the connections on both boards and also under the top door hinge. Be sure to disconnect power to the unit first. Also make sure this unit is plugged into a good three prong wall outlet and it has a good ground and the polarity is correct. By this I mean the small terminal in the outlet is hot and the larger terminal is common. If these checks are all ok, it may be a problem in the wiring in the door or the new board may be defective. In this case, I would strongly recommend having a technician check it. You can call 1-800-469-4663 to schedule a tech to come out. I hope this will help you.

Read More
Scott D -
Sears Technician
January 05, 2012
A:

I just replaced the main panel, and as feared, no impact to the front panel display. My next step was to be replacing the front board, but the above questions make me think I am headed down the same path of wasted money and time. As I said previously, I have some power indicated to that front panel, so I suspect it as the culprit, but can't know until I try it I guess. I have another question regarding repeated problems with the water reservoir that I am about to post separately.

Read More
dave -
January 06, 2012
A:

Dave, check for loose connections first as described above. If the connections are all ok, it will lead to the interface board or the wires inside the door. If there is a wiring problem inside the door, then the complete door would need to be replaced. I look forward to assisting you with the reservoir problem.

Read More
Scott D -
Sears Technician
January 07, 2012
See more answers
Q:

How old is my old Sears 9" Table saw

A:

Detailed information about your table saw can really come in handy and I will be happy to help. I did some research and I was able to find a link in where you can view the owners manual for your table saw. The expert will respond within 2 business days with more information. Thank you for your patience.

Read More
Joseph P. -
January 23, 2013
A:

On the back page of the manual, it was printed in March of 1982. So, I am going to assume, it was made in 1982. The saw is 30 years old, and stil runs like new... Gotta love Craftsman

Read More
craig -
January 23, 2013
A:

Thank you for your question. I will be happy to assist you. I looked up the model number you submitted. This model was made the 239 day of 1979.

I hope this is helpful. Please let me know ig you need further assistance. Thank you for using Manage my life.

Mark.

Read More
Mark T -
Sears Technician
January 24, 2013
A:

Hi, I was just curious, someone just offer to sell me this exact model for $70 and is it better to buy a new one? I know sort of a loaded question but I know Craftsman tools were made differently back then and just don't want to put pay $70 and then the motor go and no one can fix it because it's so old. Any insight would be nice. Thanks.

Read More
Avery -
December 13, 2014
A:

I have model 113242721 Mo295. How old is this 9" table saw

Read More
Danny -
January 16, 2016
See more answers

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show