Model #6746 KENMORE Carpet/Floor Sweepers

  • Replacement Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Power Unit Assembly for Craftsman Jack Manufacturer? 875.501390

A:

Thank you for the inquiry and for using SearsPartsDirect.com.

Based upon the model of 875.501390, this Craftsman jack was manufactured in or around year 2000. The 875 starting of the model tells us who the manufacturer of the jack is. In this case, 875 was manufactured by Florida Pneumatic.

Outside of the manufacturer for the jack, I couldn't say for sure if Florida Pneumatic manufactured the power unit or outsourced it to another manufacturer. Hopefully this information will be helpful to you.

If you have any further questions or inquiries, please don't hesitate to ask. Thanks for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
August 27, 2013
A:

All you need to do is look up the OEM Code - For many products, the first three numbers of the Model Number (usually followed by a decimal point) indicate the importer / manufacturer of the product. 875 = Florida Pneumatic - Previous Questions - 875.501390 - @ -http://www.managemylife.com/mmh/questions?q=875.501390

Read More
Anonymous -
August 27, 2013
A:

Anonymous raised a good point. The first three numbers does tell the manufacturer for any Craftsman or Kenmore product. To further expand on that, I have attached a complete source code identifier for all Sears's products. This should be of help for any appliance or product you have from Sears under Kenmore or Craftsman, or even the old Sears brand.

Source Code Identifier based upon first 3 digits

If you have any further questions, please don't hesitate to ask. Thanks for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
August 27, 2013
A:

Josh, Thanks for the reply and apologies on my late reply. Quick question for you - are there any rebuild kits for these power units? I still have my old one and I'd like to try and repair it. Any way of getting a schematic? Thanks!

Read More
Jesse -
September 16, 2013
A:

Hey Jesse, thanks for the response. 

It looks like the power unit on this Craftsman Jack is being sold as a complete unit, no rebuild kit being offered. Usually that's the case for the power units, I think the primary factor is because there would be a liability issue if someone was to rebuild them and have it fail prematurely and cause injury.

As requested, I have attached a schematic for this unit showing the parts breakdown. You will see the power unit listed as # 1 on the visual. Hopefully this helps.  

Thanks for using SearsPartsDirect.com.  

Read More
Jeff Wallace Sr -
Sears Technician
September 16, 2013
A:

Wait Josh, I meant do you have a schematic for the internals of the power unit?

Read More
Jesse -
September 16, 2013
A:

No, I sure don't. Since it's not being broken down by the manufacturer, I have nothing in regards to part numbers or visuals on it. You might be able to make contact with the manufacturer and see what they would suggest in regards to a rebuild or any internal specs/schematics for it. That would be your best bet.

Read More
Jeff Wallace Sr -
Sears Technician
September 16, 2013
A:

And that again would be Florida Pneumatic/Quality International?

Read More
Jesse -
September 16, 2013
A:

Exactly, I believe I've got thier website for you, just click here to be directed to the page I see. It gives a good contact number to call. It would be a good place to start. Hopefully it helps.

Read More
Jeff Wallace Sr -
Sears Technician
September 16, 2013
A:

Great - thanks Josh for all of your help. Should I find anything out I will post it back here.

Read More
Jesse -
September 16, 2013
See more answers
Q:

looking for parts for model 50167 4 ton low profile service jack 50167

A:

Thanks for the inquiry and for being a valued member.

I have linked the owner's manual below for this Craftsman jack, model 50167. To obtain parts, we request that you contact the manufacturer, which is Torin Jacks, Inc at 1-888-448-6746. 

Craftsman Jack 50167 Manual

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
April 29, 2015
Q:

is improper sewing machine needle likely cause of skipped bobbin stitches ? 15817511 Kenmore Kenmore sewing machine head

A:

Improper sewing machine needles are one cause of skipped bobbin stitches. Other causes include improper thread tension, improper threading, incorrect bobbin position, improper type of thread, the type of fabric and lint accumulation. 

Your details seem to indicate that the machine was working proper when using the new Singer needles. I recommend that you try using the same Singer needles and see if the machine still skips bobbin stitches. If not, then stick with the same type of needle.

If the machine skips bobbin stitches using the new Singer needles that you were using, then I recommend that you check the other issues listed above for the cause of your skipped bobbin stitches.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
November 24, 2014