Model #6743 NORGE Residential Washers

  • Control Panel
    3 Results
  • Control Panel Page 2
    3 Results
  • Top
    3 Results
  • Top Page 2
    3 Results
  • Motor And Pump
    3 Results
  • Motor And Pump Page 2
    3 Results
  • Tub
    3 Results
  • Tub Page 2
    3 Results
  • Base
    3 Results
  • Base Page 2
    3 Results
  • Transmission
    3 Results
  • Transmission Page 2
    3 Results
  • Transmission Page 3
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

water level malfunction LNC6743A71 Admiral Admiral laundry

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you.

I understand the frustration with a washer that's not working properly. Lets take a look and see what we can find. Im showing that if the washer would not stop filing with water it could be the pressure switch.

The pressure switch in the one you select your washer size with. Replacing that should solve your issue.

Hope this information has help you. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663.

Any further questions or concerns, You will have to post a new question, as I cannot reply to any comments at this time. Again, Thank you for choosing SearsPartsDirect.com.
 

Read More
Samantha A -
Sears Technician
July 16, 2014
Q:

How to test a part CYE2000AYW Magic Chef Magic chef laundry

A:

Thank you for the inquiry and for using SearsPartsDirect.com.

You can measure the resistance of the timer resistor with a volt/ohm meter to determine whether it is good. Unplug the dryer and connect the multimeter leads to the terminals on the resistor and measure the resistance of the resistor. You should measure between 4050 ohms and 4090 ohms. If not, then the resistor will need to be replaced.

If by chance the resistor will need to be replace, I have included a blue link below that you may click on to be directed to the PartsDirect page to view and purchase if necessary, hopefully this helps.

Timer Resistor for Magic Chef Model CYE2000AYW

I wish you all the best with the troubleshooting and thanks again for using SearsPartsDirect.com.

Read More
Jeff Wallace Sr -
Sears Technician
August 21, 2013
Q:

Maytag Electric dryer PYE2300AYW timer not advancing

A:

I understand that your your dryer timer is not advancing. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert. I attached the link below for you to view. I hope the link that I provided is helpful.

Read More
Alina F. -
March 03, 2011
A:

Hi, Thanks Alina, but symptoms are a bit different as is the wiring. I appreciate the effort though!

Read More
jon -
March 03, 2011
A:

Thank you for your question and I understand your concern.

Based on your model and symptom the timer is likely faulty if it will not advance in the "TIMED" setting.

If it will advance in the "Timed" setting but not during the "Auto" cycles then the resistor connected between timer terminal "A" and "R" is likely faulty. The resistor can be tested using an ohm meter. The resistor should measure 3.77K ohms.

In order to verify if the timer is faulty will require checking the voltage supply to the timer motor. I added an image below of the wiring diagram and I traced out the timer motor circuit. I also drawn a circle around the two terminals located on the timer where the voltage will need to be checked. Place one voltage meter lead on terminal "M" and the other meter lead will need to be placed on terminal "TM". NOTE: I do not recommend checking voltage unless you have experience and feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose and repair your dryer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Parts can be looked up and ordered at Sears PartsDirect

Read More
Joey S -
Sears Technician
March 04, 2011
A:

Many thanks Joey S. Yes, the timer does not move regardless of cycle. As for checking power, I am simply checking to see if the timer is getting (110?) power? If so, then it is bad. Sound right? Thanks for taking the time to write.

Read More
jon -
March 04, 2011
A:

Jon: That�s correct; you�re checking the voltage supply to the timer motor. Check across terminal M and TM. If voltage is present and the timer is not advancing, replace the timer.

Read More
Joey S -
Sears Technician
March 08, 2011
A:

I have the same problem with my dryer. Model PYE2300AYW. However, the timer advances in standard mode but not in auto dry. I found the 3.7k resistor and measured it. It is about 10 ohms with the wires disconnected on one side. The other side has two wires going to the heating element. Maybe I have the wrong resistor? If it was bad I would have expected it to be open. None of the parts diagrams I find have this resistor or the timer.

Read More
john -
December 10, 2011
A:

John: The resistor is a non illustrated part. It is not shown in the parts diagram. The part number of the resistor is 63-6743. The resistor should measure 3.77 K Ohms. It does not have to fail open to be faulty. The timer motor should have voltage applied to it whenever the operating thermostat opens or in other words when the heating element cycles off when it reaches operating temperature.

Read More
Joey S -
Sears Technician
December 10, 2011
A:

Do I have the right resistor? I am measuring the one next to the heating element. This may be the ballast resistor? It has two wires on the left side going to the element and two wires comming in from the right side. Do I need to open console? I am also confused as to how this resistor could possibly help in auto drying. There is no moisture sensor at all on this dryer.

Read More
john -
December 10, 2011
A:

John: When the operating thermostat opens, the resistor acts like a Neutral and completes the circuit to the timer motor. The resistor is usually located inside the control panel. One end of the resistor will connect to terminal R on the timer and the other end of the resistor will connect to terminal A on the timer.

Read More
Joey S -
Sears Technician
December 10, 2011
A:

I measured the resistor at 3.75k. This is within 5% so I am assuming the resistor is good. Maybe the timer assembly is bad?

Read More
john -
December 11, 2011
See more answers