Model #66595781000 KENMORE Free Standing, Electric

  • Cooktop
    3 Results
  • Door
    3 Results
  • Chassis
    3 Results
  • Control Panel
    3 Results
  • Drawer
    3 Results
Find part by diagram >

Question and Answers

Q:

Oven will not turn off. Dangerously high heat. 66595781000 Kenmore Electric range

A:

Thanks for the inquiry and for using SearsPartsDirect.com.

I am sorry to hear that the oven is continuously powered, even when the control is not turned to heat.

In this particular instance with the symptom you have, it sounds like the electronic control board would need replacement. The heating contact is likely welded closed.

If it was a temp sensor, the oven would still turn on and off based upon the control; however, with the control not having functionality, it's not a sensor issue, but a control issue. 

The part number for the electronic control is 8523665. In this situation, we would recommend having a service technician help assist with the repair, as these boards are very sensitive and can be damaged easily during installation by electrostatic discharge.

If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-469-4663, or click here to be directed to the page to set up service.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
November 06, 2014
Q:

electric range 665.95781000

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your oven and I do understand your frustration. Glad to help out. I'm looking at your model number 66595781000 and if the oven is cool when you set the oven to clean and the oven door will not lock and the Lock light is flashing, the door may not be shut enough to push and close the door switch. Try pushing inwards on the top of the door while programing a clean cycle to see if the door will lock. If the door does not lock, it could have a faulty electronic oven control or a faulty door lock motor assembly. In order to diagnose if the lock motor is getting voltage after setting and starting a clean cycle will require a voltage meter. The voltage can be measure to the door lock motor from the electronic oven control board. You would have to measure the voltage supply across black wire with the white stripe and the solid white wire at the electronic oven control board. 


NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I strongly suggest calling a service technician to diagnose and repair your oven. 

If 120 VAC is measured and the door lock motor is not running, the door lock assembly will need to be replaced. If 120 VAC is not measured across the black wire with the white stripe and the solid white wire, I suspect a faulty electronic oven control board.  I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

Read More
Sherman_G_Wallace -
Sears Technician
October 07, 2014
A:

When I try to start the cleaning, after a minute or so error message shows "E1 -F5-". not for sure if I need to order latch-mtr (3196953) or what part I need. Thank you for any help

Read More
Kathy -
October 07, 2014
See more answers
Q:

Broiler 66595781000 Kenmore Electric range

A:

Thank You for choosing Sears PartsDirect.com. It is unfortunate to hear that you are having issues with your range and I do understand your frustration. Glad to help out. I'm looking at your model number 6659578100 and the broiler circuit is controlled by the electronic oven control board. Since the broiler is turning on by itself, this indicates a failure in the electronic oven control board (clock/timer). With the power supplies shut off to the range, inspect the bake and broil element for any signs of blistering or cracks. If one of the oven elements burns out and shorts to ground, a portion of the element can remain on. Click here for image of the panel.  There could be one of two possible failures causing the broil element to not turn off.
1.Stuck contact on the K-4 broil relay (Part of control board)
2.The broil element has failed and is shorted to ground.
Unplug the range and then open the oven door and inspect the broil element visually and by feeling of the entire broil element. If the broil element has any blisters or appears to have blown open, replace the broil element. If the broil element feels smooth and it has no apparent defects or blisters, replace the oven control board (key#12). I have included a link to our Parts Direct page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information.
 
Thank you for choosing Sears PartsDirect.com.
 
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.
 

Read More
Sherman_G_Wallace -
Sears Technician
July 25, 2014
A:

Thank you your information is very helpful.

Read More
HELEN -
July 26, 2014
See more answers

Top Parts