Model #66595029101 KENMORE Free Standing, Electric

  • Cooktop
    3 Results
  • Door
    3 Results
  • Chassis
    3 Results
  • Control Panel
    3 Results
  • Drawer And Broiler
    3 Results
Find part by diagram >

Question and Answers

Q:

Error code on oven

A:

I understand that your oven has an error code displayed. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
October 06, 2012
A:

You may have a problem with the electronic control board. You are correct that the E1F5 code indicates that the control detects a problem with the oven door lock circuit.

I recommend that you try to reset the control board in that range by unplugging it for 3 minutes. Restore power and see if the control works properly.

If the range still does not heat properly, I recommend that you unplug the range and check the resistance of the oven temperature sensor probe using a volt/ohm meter. You can access that oven temperature sensor probe as shown in the first image below. You can also access the wires going to that sensor probe from the back of the range. Remove the back panel to access that component (with the range unplugged ) if you do not see mounting screws on the inside of the oven cavity. Measure the resistance of the probe. It should measure around 1080 ohms at room temperature. If the resistance of that sensor is off by more than 50 ohms then it will probably need to be replaced. You can order parts from this page: Kenmore Range Model 665.95029101 Parts . Be sure that you unplug the range before accessing and replacing internal components.

If that sensor is okay, then you may need to replace that control board in the console. Reply with additional details if you need more assistance.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
October 08, 2012
See more answers
Q:

Error code meaning?

A:

Error codes can be confusing. I found a similar question from a previous answer that may help. I attached the link below. Hope this helps!

Read More
Barbara H. -
October 16, 2010
A:

I understand your concern. The fault code "F2-E0" implies a key was held down too long or the key pad has a shorted key. I added the error code explanation from the technical data sheet for your model in the image below. The failure could also be the oven control board and not the key panel.

In order to possibly diagnose which one has failed will require following the instructions in the image below. You would have to disconnect the power supply and then gain access to the oven control/clock and disconnect the key pad harness connector from the control board and then reapply power. If the fault code recurs, replace the oven control. If the fault code does not recur, replace the touch/key panel.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
October 18, 2010
See more answers
Q:

My Kenmore stove, model number 665.95029101, is displaying the error code EO F2. What does this mean and how can I fix it?

A:

In reference to your Kenmore stove, model number 665.95029101;

Error code E0-F2 : Key held down too long or shorted key

  1. Verify failure if not displayed, using CANCEL/OFF key. Press key for 5 seconds until last error code is displayed.
  2. Disconnect power longer than 30 seconds
  3. Unlock keytail connector. Inspect connector locking tabs and keytail end for damage. Ensure locking tabs are not bent or broken and keytail is not creased or torn.
  4. Reinsert keytail into connector. Ensure keytail is fully seated before locking down the connector. Once locked, tug keytail slightly yo ensure lock.
  5. Re-apply power and observe for longer than 1 minute
  6. If any false key presses occur or the failure remains, disconnect power, and replace keypad.
  7. repeat steps 3-6. If failure repeats, disconnect power and replace control.

Read More
Angela R. - Personal Solutions Manager -
Sears Technician
October 14, 2009

Top Parts