Model #66592153300 KENMORE Free Standing, Electric

  • Cooktop Parts
    3 Results
  • Door Parts
    3 Results
  • Chassis Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Drawer & Broiler Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Install part num 8524212 66592153300 Kenmore Electric range

A:

Thank you for choosing SearsPartsDirect.com. Thank you for your question. I know how important installation instructions are when replacing the control board.

Disconnect the key pad ribbon and the rest of the wires. In the middle and at the bottom, behind the board is a metal lever. Pull this lever down. Push in on the board and slide to the left. Pull the top out and down. The metal pins will slide thru the top slots and then thru the bottom slots. Reverse the procedure to install the new board and push the lever up to lock in place. Reconnect the ribbon and wires.

If you do not feel comfortable making the repair yourself, I recommend a tech go out to  your home. If you would like a Sears technician to complete the repair, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663.

I hope this helps you. Have a great day.

Read More
Samantha A -
Sears Technician
April 18, 2014
Q:

Kenmore Electric Range Model # 66592153300 - Broiler Element Not Working 66592153300

A:

It can be extremely frustrating when your oven will not produce any heat. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
November 29, 2012
A:

That link for a previous answer that Julio posted in the above response discusses a similar failure. It provides a wiring diagram for your same model of range. Your range does have a thermal fuse in the broil element circuit that would prevent that component from heating even though the bake element will continue to heat. You can unplug the range and access that fuse by removing the outer back panel on the back of the range. Check that fuse using a volt/ohm meter. It should measure near zero ohms of resistance (continuity). If it measures OL -- open load or infinite resistance then that fuse if blown and it will need to be replaced. If the fuse is okay, then you could have a bad broil relay on the electronic oven control board in the console of the range.

You can order parts from this page: Kenmore Range Model 665.92153300 Parts . Be sure that you unplug the range before accessing internal components and replacing parts.

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 30, 2012
See more answers
Q:

My kenmore 665.92153300 oven will not heat. The stovetop works fine. I used the oven yesterday with no issues.

A:

The Managemylife web site is a good resource of information to find out what may be happening and what options are available to you. I'm sorry to hear about the difficulties with your Kenmore oven. I did some research at Managemylife website and found two expert answers to a similar question that may help until your expert can respond. I have attached the links below so you can check it out. If you decide to schedule service, and have a qualified technician to assist you, I have attached the link to searshomeservices.com. I hope this will be useful until your expert can respond

Read More
James -
May 05, 2012
A:

Thank you for your question and I understand your concern.

If neither bake nor broil element will get hot, I suspect a faulty electronic oven control or the thermal fuse has failed.

I added an image of the wiring diagram and the bake and broil strip circuits. The thermal fuse is located behind the rear panel and it should be disconnected and measured for continuity with an Ohm meter. If the thermal fuse measures continuity, you should disconnect the bake and broil elements from the rear of the range and measure them both for continuity. If the oven elements measure continuity, I suspect a faulty electronic oven control.

NOTE: Disconnect the range from the power supply before removing the rear panel and making the continuity checks.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
May 07, 2012
A:

I have the same problem. My wife says that the display went haywire first and now its back to normal with everything working except the oven. Maybe you can narrow it down the part that needs to be replaced with this info. Thanks.

Read More
Anonymous -
September 17, 2012
A:

Anonymous: In order to provide any specific information or parts I will need to know the full model of your range/oven. Based on the limited details it could have a loose wire connection or faulty electronic oven control. So that�s what I can tell you at this point. I can give you more detailed help if you could provide me with the complete model number. If you could supply me with that information I will be happy to assist you further.

Read More
Joey S -
Sears Technician
September 17, 2012
A:

Hi thanks for the response. Model 65592153300

Read More
Anonymous -
September 17, 2012
A:

Here is a link to the oven.

Read More
Anonymous -
September 17, 2012
A:

Anonymous: Just for your information, the model number is 665.92153300 and not 655.92153300. If the electronic oven control/clock asembly is working correctly at the moment, I suspect an issue with the touch panel/menmbrane switch or the connections at the control board.

Read More
Joey S -
Sears Technician
September 17, 2012
A:

Thanks. It just stays on preheat when I select to use the oven.

Read More
Anonymous -
September 24, 2012
A:

Anonymous: If the bake and broil element will not produce any heat, I would suspect the thermal fuse is faulty. The thermal fuse can be disconnected and tested for continuity with an Ohm meter. The thermal fuse is located on the back of the range. I added an image below showing where the thermal fuse is located. Disconnect the power cord from the power source before removing the panel from behind the range. Disconnect the two wires from the thermal fuse before measuring across the thermal fuse for continuity.

Read More
Joey S -
Sears Technician
September 24, 2012
See more answers

Top Parts