Model #66592022100 KENMORE Free Standing, Electric

  • Cooktop
    3 Results
  • Door
    3 Results
  • Chassis
    3 Results
  • Control Panel
    3 Results
  • Drawer And Broiler
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Electric Range

A:

This is a great site to get step by step instructions for replacing parts. I would recommend waiting for the expert to review and confirm the diagnosis. The expert will then provide step by step instructions for this specific model. As per the previous post, if you do not feel comfortable doing your own repairs, an option is Sears Home Services at the link below.

Read More
Barbara H. -
April 20, 2012
A:

The Sears representative that you talked to is probably correct about the EOC clock control board being bad. There is a chance that a bad oven temperature sensor could also be causing that problem. If you want to perform some more diagnosis before replacing that EOC clock control, then you can check to see if the broil function is working properly. Lower the temperature to 300 degrees or less when checking that broil function. Close the oven door and check that broil function to see if that element cycles properly. If the broil element cycles on and off properly but the bake element stays on constantly and overheats, then replacing that EOC clock control board should fix your problem. You can order that control board from this link: EOC Microcomputer for Kenmore Electric Range 665.92022100 . Be sure that you unplug the range before accessing and replacing that control board. Here is a link for a repair video that shows how to replace that part: Kenmore Range Clock Control Replacement .

This information should help you fix that range problem. If you need more assistance, reply with additional details.

If you get to a point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
April 23, 2012
A:

Lyle, The oven wouldn't work last week Thursday. I turned off the breaker until Sunday. It worked good Sunday night but turned off the breaker just in case there was a problem. Turning on the breaker on Monday it worked just fine again. This time I checked it how you mentioned. So why would it magically be fixed? Any thoughts or suggestions? Thanks

Read More
Lacey -
April 23, 2012
A:

I should mention that last week Thursday I did turn the breaker on and off and the oven would run whether we physically turned it on or not. The other nights (Sunday and Monday) everything worked just like it should. If turned on it turned off and the elements appeared to be cycling on and off like expected.

Read More
Lacey -
April 23, 2012
A:

Hello Lacey. Turning off the breaker to completely disconnect electrical power from that clock control board probably reset that board. That is why the relay was no longer sticking in the closed position and causing the element to heat constantly. The control board will probably work properly going forward. If you encounter the same problem again, then you may need to replace that control board.

Read More
Lyle W -
Sears Technician
April 24, 2012
See more answers
Q:

My Kenmore Stove won't turn off.

A:

When the oven overheats or won't shut off, it would raise alarm. The expert will review this model and respond. I was able to locate two similar questions that may help. If you are not comfortable checking the internal components of a range like many of us, I also added the link to Sears Home Services below. I hope this information helps.

Read More
Barbara H. -
April 20, 2012
A:

Thank you for your question and I understand your concern.

If one of the oven elements happen to burn out/short, a portion of the heating element can remain on even though the oven has been turned off. If this happens it can also cause the contacts in the K4 or K2 relay to weld shut and keep the bake or broil element on. Flip the circuit breakers off and check the bake and broil elements for any signs of blisters or cracks. If the bake and broil elements look Okay, I suspect a faulty electronic oven control and it will need to be replaced.

The oven control #8523665 for Kenmore range model 665.92022100 can be ordered from Sears Parts Direct if you feel confident in replacing the electronic oven control.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 21, 2012
A:

Joey, The range didn't work Thursday and I turned it off using the breaker. Turned it back on and it didn't work. I left the unit off until Sunday. I turned on the breaker on Sunday and the oven didn't turn on (cause I never used it). In other words it was working just like it should. Just in case I turned off the breaker so the oven wouldn't randomly turn on. Well I checked out everything on Monday and then tested it and it worked complete normally. Why would it work normal now unlike Thursday? Any thoughts or ideas? Thanks

Read More
Lacey -
April 23, 2012
A:

Lacey: I suspect either the bake or broil relay contact likely stuck closed causing the oven to over heat. I would monitor the operation because it could happen again. It will likely need a new electronic oven control in the near future.

Read More
Joey S -
Sears Technician
April 24, 2012
See more answers

Top Parts