Model #66592002102 KENMORE Free Standing, Electric

  • Cooktop
    3 Results
  • Door
    3 Results
  • Chassis
    3 Results
  • Control Panel
    3 Results
  • Drawer And Broiler
    3 Results
Find part by diagram >

Question and Answers

Q:

What is error code "E1 -F5-" mean when I try to run the clean cycle on my Kenmore range?

A:

For error codes a suggestion I have is going onto your owners manual. If you do not have one just go ahead and go onto the top of this page and click on the tab that says "MANUALS" a search box should come up; go ahead and type in your model number. Your owners manual should come up and in it you will be able to find out what the error codes on your appliance mean. I have attached the link below. Hope this helps!

Read More
Alina F. -
July 09, 2010
A:

The E1 - F5 error code indicates that the oven door lock assembly is not operating. The oven will not begin the self clean cycle unless the oven door is properly locked. This failure is normally caused by a failed door lock assembly. In rare instances, it can be caused by a failed control board or a wiring failure. The normal troubleshooting for this problem is to unplug the range and check the wire harness connections between the control board and the door lock assembly. The first image below shows the access information for the components in this model of range. The second image shows the wiring diagram with the door lock circuit highlighted. If you are able to unplug the range and check the wiring connections, you can likely fix this problem yourself. If the wiring connections are okay, the next step in troubleshooting is to replace the door lock assembly (part W10107820). You can order this part from the Sears PartsDirect website. Replacing this part will likely fix your problem.

If you replace the door lock assembly and still have the same problem then the electronic oven control board may also need to be replaced.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 13, 2010
A:

My wife ran the clean cycle. It cleaned and then went to error code E1 F5 after a few hours. The door is locked and the error code shows. I can reset the clock and the stove top works. I have unplugged for several hours, replugged, put it to clean mode, it starts(after pressing start) and about a minute later, it goes back to error mode. LOCKED is also on the display. Is there a control panel that is bad? This model is 13 years old, will it be monetarily worth it to fix?

Read More
Barry -
December 29, 2015
See more answers
Q:

My kenmore oven won't shut off not the burner the oven. It gets extremely hot. The only way to get it off is to unplug it. Dangerous!

A:

The oven not shutting off can be dangerous and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
June 04, 2012
A:

I am sorry to hear that you are having this type of failure in your range. I understand your safety concern. I have forwarded this issue to our Sears Customer Care Team. They will contact you by email regarding this issue.

Although we forwarded your issue to our Sears Customer Care team, we also normally provide technical information and troubleshooting for out-of-warranty problems and failures. This may help you fix that problem yourself if you are interested in that information. Based on your description, you probably have a stuck relay on the electronic oven control board in that range. You could also have an element that is broken and that is shorting to the metal cabinet inside the oven cavity. With the range unplugged you can examine the bake and broil elements for visible damage. If an element is broken, it will need to be replaced. Here is a link for a brief repair video that shows how to replace an element (with the range unplugged ): Bake Element Replacement . Your oven elements will be slightly different than the one shown in that video but the basic repair procedure is the same. Be sure that you unplug the range before accessing internal components. You can order parts from this page if necessary: Kenmore Range 665.92002102 Parts .

If you see no visible damage to the elements, you can check them with a volt/ohm meter as shown in this video: Bake and Broil Element Testing . The elements in that range should measure between 10 and 40 ohms of resistance. If an element is bad, it will need to be replaced. If you need further help testing the elements, let us know.

If the elements are okay, then you failure is likely in the electronic control board that is housed in the console of the range. The image below shows the wiring diagram for your range with the bake and broil element circuits traced in wire colors. The element that is staying on probably has a bad relay (K-2 or K-4 relay on that control board). In that situation, you will need to replace that electronic clock control board. You can order that part from this page: Microcomputer Control Board for Kenmore Range 665.92002102 . Here is a link for a brief repair video that shows how to replace that component: Range Clock Control Replacement . Your range will be slightly different than the one shown in that video but the basic repair procedure is the same. Be sure that you unplug the range before accessing internal components.

I hope that this do-it-yourself repair information helps. If you want to repair this failure yourself and you need more assistance, reply to this thread with additional details.

I looked at the components in this range from a technical perspective. I see that the L2 leg of power in that broil circuit has a thermal fuse. That would prevent that broil element from heating constantly if it reaches a temperature that blows that fuse. That safety feature may not prevent the oven from heating constantly in your situation if the bake element is shorted out or the bake relay on the control board is bad. The L2 leg of power on this range is constantly supplied to the bake and broil elements. That is why the thermal fuse is in place for the broil element. The safety features of the range will normally prevent a fire or a dangerous situation. I hope that this safety information helps. If you have further questions about that issue, please let me know.

If you do not want to fix this problem yourself, you can have a Sears Technician examine and repair this failure. Here is a link for the Sears Service website: Sears Home Services .

Read More
Lyle W -
Sears Technician
June 06, 2012
A:

I have a Kenmore gas range 665.72014 that would not shut off and continue letting gas flow even after unplugging it. The door locked and would not open until cool. Shut gas off for the unit and when cool plugged in the electric. I got an E2 and F3 error code at same time. Would like to know what these codes are. Thanks!

Read More
Tim -
August 10, 2015
See more answers
Q:

The light for the oven temperature is out. I was told to order the lens light # 3196068. That is not correct Kenmore Electric range

A:

Thank you for choosing SearsPartsDirect. I can certainly understand how frustrating it can be when you cannot see the temperature on your range. I did look into the model number you have provided and I have found that you wil need to replace the control board in order to get the temperature to light up. 

The control board controls the oven as well as the temperature display. 
 

Click here for the board. 


You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
July 14, 2014

Top Parts