Model #66575843005 KENMORE Free Standing, Gas

  • Cooktop Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Manifold Parts
    3 Results
  • Chassis Parts
    3 Results
  • Warming Drawer & Broiler Parts
    3 Results
  • Door Parts
    3 Results
  • Optional Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore gas range model #665.75843005 not lighting manually

A:

I am sorry that you are having some difficulties with your range and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your range troubles while you wait for your expert response.

Read More
Joseph P. -
November 03, 2012
A:

There is an electrical solenoid on the back of the range that will stop gas flow to the cooktop if power is lost. This is on the tech sheet, so I guess the manual is wrong...

Read More
Chat in RI -
November 03, 2012
A:

Thank you for your question and I understand your concern.

The information in the Use and Care Guide about being able to light the surface burners pertains to models that do not have a cook top lock out control. Your model has cook top lock out feature and a cook top lock out gas valve. When the power is out, your surface burners can not be lit with a match because no gas will flow. The range must have a voltage supply in order to open the cook top lock out valve. In the event of a power failure; the gas supply to the surface burners will be shut off.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 05, 2012
See more answers
Q:

My power went out and when it came back on my Gas Oven/Range would not turn on just made a loud buzz. Its a Kenmore model 665 75843005. Any idea how to fix?

A:

Power outages play havoc with transformers. A failed transformer will shut the unit down completely. I know and sympathize with the fact that this also effectively shuts down your ability to cook for your family. I provided a link below that will discuss this matter with more detail. The model numbers are not the same but the issue is the same mechanically. You will also hear from our expert team within a day or two. Until then, have a pleasant morning.

Read More
Henry -
September 23, 2012
A:

Henry could be correct about that transformer being the source of the buzzing. The transformer on the main oven control board is shown (circled in red) in the first image below. You can unplug the range and remove the upper back panel behind the console. Here is a link for a previous answer that shows how to access that control board: how do i remove board on range . Briefly plug in the range and see if you can determine whether that is the actual source of the buzzing noise. Do not make any contact with any wiring or components while the range is plugged in with that panel removed. Unplug the range as soon as you check that issue .

If that transformer on the oven control is buzzing, this indicates that the oven control board is apparently getting power. Since the control board is apparently getting power but the display is not lighting up, the control board (part 8523666) will probably need to be replaced in that situation. You can order that part from this page: Kenmore Gas Range Model 665.75843005 Parts . Be sure that you unplug the range before accessing and replacing internal components.

Note: The cooktop burners will not work if the oven control board is bad. Your range has a relay for the cooktop burners that will lock out the gas supply valve during a power outage. If the oven control board in the console will not power up and work, that relay cannot be "electrically closed" to open that gas valve and supply the cooktop burners with gas. Once you fix the problem with the oven control board, the cooktop burners will probably work properly.

If that transformer on the electronic oven control board is not buzzing, then there is a chance that the main control board is not getting power. The wiring diagram for the power supply to the oven control board. The voltage supply to the control board goes through a relay on the back of the range as shown in that diagram. I highlighted the voltage supply with a small red line since that wire is traced in black (the true wire color). The neutral connection is traced in white with a small green line to highlight the wires. You could have a wiring failure in that circuit. A problem with the relay could also prevent the control board from getting power. To check the power to that control board, you will need to perform a live voltage check using a volt/ohm meter. NOTE: You should only check that live voltage if you are completely confident in your technical ability to safely measure it. Wear electrical safety gloves and safety goggles when checking that live voltage. Unplug the range as soon as live testing is completed . If that control board is getting 120 volts through the black and white wires but will not power up the display, then the control board will need to be replaced. If the control is not getting power, then you can check for power at the relay using that wiring diagram as a guide. If that relay is getting power and the control board is not getting power then that relay (part 9752759) will need to be replaced (assuming that the wires in that circuit are intact and connected properly). Be sure that you unplug the range as soon as live testing is completed.

These tips may help you determine the cause of your range problem. If you need more help, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 25, 2012
See more answers
Q:

My Kenmore gas oven won't stay lit.

A:

I'm sorry about the difficulties that you are experiencing with your oven. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. If you would like assistance from a qualified technician I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
January 04, 2011
A:

Thank you for your question.

I am so sorry to hear that this problem with your range ruined your Thanksgiving. I am relaying your concerns to our customer service team who can help address this for you. I´┐Żll get back to you to let you know what the outcome is.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
January 06, 2011
See more answers

Top Parts