Model #66575832001 KENMORE Free Standing, Gas

  • Cooktop
    3 Results
  • Door
    3 Results
  • Control Panel
    3 Results
  • Manifold
    3 Results
  • Chassis
    3 Results
  • Warming Drawer And Broiler
    3 Results
Find part by diagram >

Question and Answers

Q:

oven door remains in the locked mode after the self cleaning cycle has been done about 24 hours ago

A:

Error codes can be an inconvenience and keep your range from working properly. I did some research and I was able to find a link with a similar question. I hope this helps with your research while you wait for your expert response. 

Read More
Joseph P. -
March 14, 2013
A:

Thank you for your question and I understand your concern.

The E1/F5 fault code will flash if the door lock motor assembly is not operating. 

NOTE: Disconnec the range from the power supply before servicing. 

I added an image below with the procedure of accessing the door lock motor assembly and how to diagnose the failure. It will require making voltage measurements and I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your range. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
March 15, 2013
See more answers
Q:

Model #66575832001 - Kenmore Gas range My range is getting an F3 E0 error plus its hung in Clean cool mode.

A:

I know how concerning it is when your range is displaying an error code. I researched your question and was able to find a couple helpful links that will provide you with infatuation regarding the E0 F3 error code. I attached the links below. I hope this helps.

Read More
Jackie S -
March 18, 2012
A:

The F3 E0 error is an indication the electronic control (clock) is receiving the wrong indication from the oven sensor.

I recommend you ohm the oven sensor from the clock connections. If the resistance of the sensor is between 100-1200 at room temperature, replace the clock. Sometimes the problem is in the wiring between the sensor and the clock.

I am sending an image from the tech sheet on the range. I hope this information helps.

Read More
Jimmy K -
Sears Technician
March 19, 2012
See more answers
Q:

color codes for leads on 9758080

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
November 19, 2011
A:

Thank you for your question and I understand your concern.

I added a couple of images below with instructions on how to access the surface igniters.

The Direct Spark Ignition Control (DSI) has a J1 connector which J1 harness connector will plug into. It will have 9 wires connected all in one harness plug.

The top burner electrodes will connect to 4 terminals on one end of the control as shown in the images below. (NOTE) the wire diagram does not show the colors of the spark electrode wiring. You will need to look at the color of the wire connected to the Bake and Broil igniter in order to know where to connect them at J4 and J3 terminals.

The DSI control board will have three other terminals marked GND (ground/Green); BROIL and BAKE. The lead connected to the Broil igniter will connect the BROIL terminal (J4); the lead connected to the BAKE igniter will connect to the BAKE terminal (J3).

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 21, 2011
See more answers

Top Parts