Model #66575002102 KENMORE Free Standing, Gas

  • Cooktop Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Manifold Parts
    3 Results
  • Chassis Parts
    3 Results
  • Door Parts
    3 Results
  • Drawer & Broiler Parts, Miscellaneous Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Power Burner and SURESIMMER use

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the range. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Barbara H. -
November 27, 2011
A:

At the very top of page 5 of the owner's manual for your range, it states "This manual covers several different models. The range you have purchased may have some or all of the items listed. The locations and appearances of the features shown here may not match your model." If the knobs do not have the option of turning to a specific feature, then your range doesn't have it. I hope this helps.

Read More
Korinna S -
Sears Technician
November 29, 2011
A:

Then why do the knobs say "power burner" and "Suresimmer"? Are these burners purely dedicated to these options? The one burner with "SureSimmer" on it seems to be a very low power burner compared to the rest.

Read More
davekMN -
December 11, 2011
A:

If the knobs on your range have this option, and they do not turn to the selected setting it is possible the knobs are not on correctly. You can try removing the knobs and readjusting them accordingly. These options are dedicated to that specific burner. The SureSimmer burner should only be used to simmer and the burner will have a very low flame compared to the other burners. I hope this helps.

Read More
Korinna S -
Sears Technician
December 15, 2011
See more answers
Q:

Range keeps saying PF while using oven

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
aashe -
November 27, 2011
A:

The circuit for the range and washer is being over powered. This is why the power fails when you are using both. It is recommended that the range be on this own separate 10 amp breaker. You can see this in the image below. You will either need to have a licensed electrician install a new breaker, or don't use the washer and range at the same time. If you need further assistance, please reply to this thread.

Read More
AnneJ -
Sears Technician
November 29, 2011
A:

Okay, we were not running the washer or anything else on that circuit, and it still PF'd. It seems to do it when the oven lights to maintain heat. It never does it at Preheat. But it will often do it right after preheat. Other times it will do it in the middle of a baking time, again when it fires to maintain temp. How can I determine if it is the oven control panel or the electrical circuit. I also tried plugging it into another circuit and it seemed to work fine for a while, then started doing it again.

Read More
davekMN -
December 11, 2011
See more answers
Q:

Gas Oven does not light

A:

I know that it can be difficult to have your appliances stop working properly. While you are waiting for your expert answer, I have found a link that will provide some information and troubleshooting for the problem. It sounds like the ignitor has gone bad. The link will show you what to look for to determine this. I hope this helps.

Read More
aashe -
September 19, 2011
A:

That link for a previous answer that Aashe posted in above response covers a similar failure. In your situation, it is likely that you have a problem with the igniter and burner assembly (part 8190618). Replacing that part will probably fix the failure that you are describing. You can order that part from the Sears PartsDirect website.

Be sure that you unplug the range and shut off the gas supply before replacing that burner/igniter assembly.

Here is a link for a video that shows how to complete that repair: Range Bake Spark Electrode and Burner Replacement .

This information should help you fix the range. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 21, 2011
A:

I had that same problem and I put in the new burner and spark electrode and that did fix the problem. Why did the orignal burner and electrode need to be changed and was that a safety hazard?

Read More
Anonymous -
September 27, 2011
A:

The original burner and electrode were modified to provide a more dependable ignition. More gas ports were provided around the igniter so that the flame could be properly detected. There was no safety issue involved with this problem. The safety gas valve will not stay open unless a proper flame is detected. This revision simply makes it easier for the ignition and control system to detect the flame. I hope that this explanation helps. If you need further assistance, let us know.

Read More
Lyle W -
Sears Technician
September 27, 2011
See more answers

Top Parts