Model #66517849400 KENMORE Dishwasher

  • Frame And Console Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Tub Assembly Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Dishrack And Water Feed Parts
    3 Results
  • Lower Dishrack Parts
    3 Results
  • Cabinet Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Faucet Adaptor

A:

I completely understand your need fro a faucet adapter for your dishwasher. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
May 27, 2013
A:

I found the part on my own!

Read More
Karen -
May 28, 2013
A:

In case anyone out there needs a faucet connector for their Kenmore dishwasher here it is: PS3407202.

Read More
Karen -
May 28, 2013
A:

Thanks for contacting ManageMyLife.com. I know how important it is to have the right parts for your appliances. I see you were able to locate the needed adaptor. Great job in finding that.
 
Please feel free to let me know if you need further assistance.
 
Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
May 28, 2013
See more answers
Q:

Kenmore Dishwasher. 66517849400 ordered Control pannel with Electronics: 8559958, but not sure if was cased by motor failure or low Voltage conditions.

A:

I know how stressful appliance issues can be. I researched through the website for an answer to your question and was unable to find any information that would be helpful. An expert will respond to your question. It usually takes 24-48 hours to receive a response. Have a good day.

Read More
Jackie S -
July 29, 2012
A:

Thank you for your question and I understand your concern.

Low voltage and voltage spikes could cause a failure in the electronic oven control. The substituted control board will fit the original control panel. Also, the control panel houses the active overlay (buttons) and not the electronic control board.

The technical data sheet is usually supplied with the dishwasher. If it's not up in the console area then it is likely up under the tub in the front area. I added a couple of images below with the technical data from the tech sheet. It will have the Ohm values of the components. NOTE: Disconnect the power supply from the dishwasher before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
July 31, 2012
A:

Thanks Diagrams really helped, wish I seen them before ordering part, Turns out there is a Thermal fuse for low voltage protection. Still have yet to order it. Tested it meter and definitely blown. Not sure yet if board is bad. Even though found primary issue still going to go through check Ohm Readings on motor to make sure overheating of wires was only from low voltages not from motor and/or/if it was also damaged. Though have to pick up new probs. I pulled old Meter out and found probes wires cut and tip broken. Guess bad thing do come in three. Though the Diagrams makes it really is to fix, Thank you! Nice to have Factory reading on Ohms. Most times only can use Amp readings in my line of work, this makes tracking down problem so much easier!

Read More
thomashunt -
August 17, 2012
See more answers
Q:

I have Kenmore Portable Dishwasher Model # 665-17849400.

A:

When a dishwasher goes out, I usually see money going out the window, either in repair cost, or replacement. Managemylife.com can take the mystery out of the repair. Your expert can help you determine if you should consider replacing or repairing an appliance. I did some research for you at this web page and found an expert answer to a similar question which may shed some light on the problem. If you decide to schedule service, and have a qualified technician to assist you, I have attached the link to searshomeservices.com. I hope this will be useful until your expert can respond.

Read More
James -
May 18, 2012
A:

The fill and drain assembly come as a one piece assembly called a coupler. I don't believe you will need to remove the cabinet to replace this piece. The image below may be helpful to you.

Read More
Fred M -
Sears Technician
May 19, 2012
See more answers

Top Parts