Model #66517572202 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

front cover 66517572202 Kenmore Undercounter dishwasher

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your dishwasher. Upon researching model 66517572202; part#W10301577 is for a stainless steel door and it does fit model# 66517572202. I have posted a link below of the door.

I trust this information will help you, Thank you for choosing Sears.

Read More
Jeff Wallace Jr -
Sears Technician
December 02, 2014
A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about the front cover for your Kenmore dishwasher model 66517572202. I will be happy to help you with this.

The part number W10301577 is the manufacturer’s replacement stainless steel front door panel for your dishwasher. It replaces the original stainless steel panel part number 8171777. Because it is the manufacturer’s replacement part it is guaranteed to fit. I have included the link below for you to view and order the part.

Stainless Steel Door Panel for Kenmore Dishwasher 66517572202

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
December 02, 2014
See more answers
Q:

Heating element doesn't heat water for washing, continuity is good 66517572202 Kenmore Undercounter dishwasher

A:

Thank you for your question.  I am sorry for the problem with your Kenmore 665.17572202 dishwasher.  From the description you give I agree the water heat does not seem to be happening.  You do not mention which cycle  but try the Pots and Pans cycle with Hi-Temp Scrub and Sani Rince selected.  The cycle should run much longer and you should notice some steam and water hotter than hot tap water.  The water heat circuit consist of the control board relay, the high-limit thermostat, element and on some models even the neutral side door switch.  The image below shows the water heating circuit.  Does the element get hot in the Dry cycle?  Be sure the Air Dry option is not on.   I hope this helps.  At some point you may need to actually check voltage to the element during a water heat or dry cycle if a meter is available.   I hope this helps.  You can reply below with any additional details for further assistance.  Thank you for using Manage My Life.  If no meter is available then you might consider having the problem repaired in your home by a Sears technician.  Here is the link: Sears Home Services Dishwasher Repair

Read More
Fred M -
Sears Technician
October 22, 2013
A:

Fred, Thanks for your help so far. I took your advice and ran the pots n pans cycle with the high temp scrub, and to my surprise, the water temp started climbing, up over 140. About 20 minutes into the wash, the machine shut off, and there was no response from any buttons, no lights, no nothing. I tried unplugging the washer. Tried a different outlet. The outlet is powered (tested the toaster). Maybe the high limit? Is there another step I can try before I bring out the technician?

Read More
Jason -
October 23, 2013
A:

From the description you give I suspect the thermal fuse blew and needs to be replaced. If there are no lights then the thermal fuse is likely bad. The temperature rising to 140 degrees should not cause the thermal fuse to open. The Sani Rise cycle can reach as high as 160 degrees. The thermal fuse is located in the console area and can be checked for continuity if a meter is available. There is a trick to checking the fuse if no meter is available. Let me know if you would likel to learn this trick.

Read More
Fred M -
Sears Technician
October 27, 2013
See more answers
Q:

Clean light blinks and dishwasher won't run?

A:

I know that it can be very frustrating to have issues with your dishwasher. The blinking clean light indicates that the control board did not see an increase in water temperature during the water heat intervals. It could have an intermittent neutral door switch operation, a bad heating element or a failed control board. Running the diagnostic test will reset the control board but it will happen again if it does not detect a temperature rise during the heating intervals.

To reset the control: Press these buttons in this order, High Temp - Air Dry - High Temp - Air Dry and then allow the dishwasher to run. When you hear the wash motor start and run for the third time the heater should come on. Let it run for a minute or two and then open the door and carefully check to see if the heating element is hot. If it's not hot, the element will need to be disconnected and tested with an ohm meter. It should have 10-30 ohms of resistance if it's OK. If it's OK the likely failure is an intermittent closing of the neutral door switch. The neutral door switch is used to make and break the neutral circuit to the heating element. Sometimes the door strike can be bent downwards just a little and it will cause the neutral door switch to close when the door is shut. The door strike is mounted at the front center area of the tub frame. Bend it down but not too much or it will bottom out against the inner door liner and the door won't be able to shut and latch. If you don't feel comfortable doing this yourself, please click on the link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using ManageMyLife.com.

Read More
AnneJ -
Sears Technician
August 27, 2013

Top Parts