Model #66517519200 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore model 66517519200 won't dry. Sanitized flashing light on end of cycle

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
June 15, 2013
A:

Hello Ann. I am sorry to hear about this problem that you are having with your Kenmore Dishwasher Model 665.17519200.

 

The sanitized light will blink when the water temperature did not reach the required sanitation temperature. It will also blink when the sanitation temperature is reached but that temperature was not maintained for the required amount of time to properly sanitize the dishes.

 

Since that sanitation light is blinking, I recommend that you check the heating element for visible damage. If that element is bad, then it will need to be replaced, Shut off the house circuit breaker for the dishwasher before accessing internal components and replacing parts.

 

If that heating element is working properly, you could have a number of other issues that would cause this problem.

 

Keep in mind that plastic items will not retain heat and they will not dry in the dishwasher like the glass, ceramic and metal items will dry.

 

Make sure that you are using rinse aid.

 

Check the water fill level in the dishwasher. Start a cycle and allow the dishwasher to fill. As soon as the filling stops, crack open the door to stop the cycle. Open the door fully and check the water level in the bottom of the tub. It should be within 1/4" to just touching the bottom of the heating element. If that water level is too low, then you may have a problem with the water supply or the inlet water valve.

 

If the water level is okay, then you can check the inlet water temperature as shown on page 12 of your owner's manual.  If that water temperature is too low, the dishes will not dry properly.

 

Several other issues could affect the drying process in your dishwasher. If you need more help, let us know.

 

If you get to the point where you need to have a service technician examine and repair the dishwasher, you can schedule service through this link: Sears Home Services Dishwasher Repair.

Read More
Lyle W -
Sears Technician
June 17, 2013
See more answers
Q:

heater element installation 66517519200

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina -
October 06, 2012
A:

You will most likely want to partially un-install the dishwasher to change the element. You will want to pull the unit out from under the cabinet for better access to the nuts holding the element. I suspect the water, drain and electrical lines will have enough slack to allow you to pull the unit out from under the cabinet without disconnecting anything. Remember to turn the power to the dishwasher off first. I hope this helps. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
October 07, 2012
See more answers

Top Parts