Model #66517479300 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Drain Pump Shield (part 8269449) 66517479300 Kenmore Undercounter dishwasher

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your dishwasher and do understand your frustration. Glad to help out. Im looking at your model number 66517479300. I inlcuded a link of the diagram for the unit. The cover goes over the drain pump. The cover does have a screw hole for a screw that should go screwed on to the pump.

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

 

 

http://www.searspartsdirect.com/partsdirect/part-model/Kenmore-Parts/Dishwasher-Parts/Model-66517479300/0582/0130000/K0503061/00008?blt=06&prst=0&shdMod=66517479300

Read More
Sherman_G_Wallace -
Sears Technician
October 29, 2013
Q:

Kenmore dishwasher cycle won't run 665-17479300

A:

Thank you for your question.  I am sorry about the problem with your Kenmore 665-17479300 Dishwasher.  If the lights are on and it runs for 15-30 seconds then I suspect the thermal fuse is okay.  From the description you give I suspect the problem is with the control board relay or the motor.  One thing you should try is next time the unit  runs for 15-30 seconds and shuts down try to cancel the cycle and see if the drain motor runs.  This model has a circulation motor and a separate drain motor.  The drain motor should run.   Try the drain motor.  The diagram below shows the wiring to the circulation and drain motor.  You can reply below with any additional details for further assistance.   

Read More
Fred M -
Sears Technician
September 15, 2013
A:

Thanks Fred- I'm not sure if my original reply here published, so forgive me if you see this response twice. The drain motor does not run when I press cancel. It's not that the drain motor doesn't work though, because if we start and restart the dishwasher dozens of times we can get it to run the full cycle, and the drain does work then. It's more like at the moment when the dishwasher cycle stops running, all functionally stops, with the exception of the green light next to "smart wash" on the panel. The red light on the outside that indicates the cycle is running does shut off. Also- I didn't see a diagram- did you post it?

Read More
erin -
September 16, 2013
A:

Hello again. I did some more diagnosis work last night and it appears that the issue might be with the latch/closure. When the machine is running and then stops, if I push in gently on the door it starts again. If I push too much, the light goes off and it stops. Do you think the part I need is a new latch (it is functionally staying shut just fine), or is it another part that would be connected to the latch?

Read More
erin -
September 17, 2013
A:

From the description you give I would suggest you replace the 8574157 door strike and see there is any improvement. The door strike can be obtained from the following link: DoorStrikeSearsPartsDirect .

Read More
Fred M -
Sears Technician
September 17, 2013
See more answers
Q:

Kenmore dishwasher issue - no power to front panel

A:

Good morning... I can appreciate all of the trouble shooting you've done thus far... I did find a link to a model that is very similar to yours that addresses the same problem. Review what the technician has written and be aware that an expert will be responding, in more detail, within the next two business days if not much sooner. I hope this helps resolve your issue and have a nice day.

Read More
Henry -
December 04, 2012
A:

Thank you for your question and I understand your concern.

There is not fuse behind the door panel but there is one on the control board.

I added an image below of the power up circuit. If 120 volts is measured across P2-6 (BK/W0 and the white wire on P7 then it could have a faulty control panel/key panel.

If there is not voltage, the thermal fuse inside the control panel has likely failed.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 05, 2012
A:

Dishwasher fixed! the final resolutions was: 2 dangling connectorss on the wiring harness needed to be plugged in. I had tried bypassing the 'thermal fuse' but still no power. I did notice however, while following your instructions, that one of the door switch wires was plugged into a dangling connector. I thought the 2 connectors were just there for decoration, duh! Really I thought they were just included in the wiring harness for testing or 'other' dishwashers but not needed for mine. I must have pulled them out when separating the door panels w/o realizing they were plugged in. [After plugging in the connectors], When I powered up the dishwasher it did turn on but only ran for about 5 minutes then shut down, ugh! As a last resort I switched polarity on the thermal fuse wires and then things began working properly. The dishwasher made it though the complete cycle. Life is good again! Thanks for the help. Oh yea, why did I pull apart the door?....I was trying to figure out where the 'broken door spring cord' was connected w/o moving the dishwasher out from the counter. A parting thought for all you troubleshooters: LOOK FOR THE OBVIOUS!

Read More
ed -
December 05, 2012
A:

Ed: You did a great job of diagnosing the issue. Have a great day and thank you for using Manage My Life.

Read More
Joey S -
Sears Technician
December 05, 2012
See more answers

Top Parts