Model #66517364301 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dishwasher operation time

A:

It can definitely be frustrating when your dishwasher is running long wash cycles. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. I hope the links that I provided are helpful. Have a great day!

Read More
Alina F. -
December 09, 2011
A:

Hi Robert,

Thank you for submitting a question to Manage My Life.

It can be normal for a dishwasher to take well over an hour and a half to run a cycle. The length/times will vary depending on the cycle selected, soil level, water temperature and options selected. If the water temperature is 120 degrees minimum as it enters the tub, it will shorten the cycle times. I have included a portion of the tech sheet below that contains information on the (estimated) cycle times. The minimum cycle time is 72 minutes and the maximum cycle time listed is over 97 minutes. This does not include thermal holds (the time it takes to raise the water temperature to the desired temperature for each cycle). The cycles can also increase with soil levels.

I recommend running the water at the tap closest to the dishwasher until the water is at its hottest, and then starting the cycle. You may also run the diagnostic cycle I included below to make sure the heater is working.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
December 10, 2011
See more answers
Q:

Kenmore Dishwasher retains a small amount of water and cause dishes to smell after completion.

A:

Smelly dishes after being washed would be cause for action. I see there are similar posts for this problem. Although they are slightly different models, I attached two below for you to check for help while your expert reviews this model and circumstances. I hope this information helps clear this smell from the dishes.

Read More
Barbara H. -
September 16, 2011
A:

Hi Dorsey,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

The source of the smell is most likely something in the sump assembly, but it could also be coming up through your household drain. Since your dishwasher drains into your garbage disposer, this can be the cause of smells. Here is a video that demonstrates gaining access to the sump assembly; Video . Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. clean the sump assembly out real well, and ensure that the drain hose is clear.

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance as more details become available, please reply to this post.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
September 19, 2011
See more answers
Q:

Why does the cover latch pop out and not allow the dispenser to close on my Kenmore dishwasher?

A:

The latch that holds the dispenser door shut is on the dispenser assembly. According to the description of your problem, the dispenser assembly (9744543) will need to be replaced. NOTE: This original part number for the dispenser assembly (9744543) will substitute to new part number 8558129.

Read More
Lyle W -
Sears Technician
June 04, 2008

Top Parts