Model #66517359300 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Change Detergent dispenser 66517359300 Kenmore Undercounter dishwasher

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your detergent dispenser on your dishwasher is not working properly. I did look into the model number you have provided and I have found the instructions for the detergent dispenser. 
Click here to view the instructions.

Also keep in mind you are able to locate parts, diagrams, and appliance repair help on searspartsdirect.com.

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
March 27, 2014
Q:

replacing heating element for kenmoore dishwasher

A:

That's great that you want to replace the heating element on your own. While you wait for the expert to answer i would suggest for you to look at the link down bellow. I hope that it helps in some way.

Read More
celene -
September 20, 2010
A:

It's not impossible to change the element without pulling the dishwasher out but I would recommend it for the first time.

The element nuts are located in the rear of the tub so to access then would require a long reach and you would be working blind.

I would suggest pulling the dishwasher out of its hole so better access can be obtained.

It most likely will not be necessary to disconnect the water line, drain hose or power cord. There should be enough slack to pull the dishwasher out far enough to reach the two heater nuts.

Remember to turn the power to the dishwasher off first.

To change the element on this dishwasher I would suggest pulling it at least half way out so better access is granted.

You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
September 21, 2010
A:

Thank you Fred for your helpful answer!

Read More
larry41 -
September 21, 2010
A:

Hope everything goes okay.

Read More
Fred M -
Sears Technician
September 21, 2010
A:

Thanks, it is not going to be very fun pulling it out since we tiled the floor after we put the dishwasher in......but, it has to be done! My wife has informed me that she is ready for a working dishwasher again!

Read More
larry41 -
September 21, 2010
See more answers
Q:

Why won't my Kenmore 665.17359300 dishwasher drain on its own yet will drain if I disconnect hose?

A:

From the description you give most likely you have a bad drain motor but the control relay can also be at fault.

The wiring diagram in the image below may help you with this problem. The circuit to the drain motor is highlighted. You should also note the circle and dotted line to the water valve. One thing to note is the same relay that provides voltage to the drain motor is the same relay that closes for voltage to the water valve. If the dishwasher is filling with water then most likely the drain problem is caused by a bad pump. The relay would work for one but not the other.

If the dishwasher will fill but it won't drain then most likely the problem is with the drain pump.

If you have access to a volt/ohm meter you can check the circuit across the pump and see if it is open. remember to turn the power off first.

The drain pump can be accessed and changed by removing the lower access panel. The 661658 pump can be obtained from the following link: Sears PartsDirect .

I hope this information is helpful to you but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
December 19, 2009

Top Parts