Model #66517039400 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Faulty part on dishwasher model 66517039400

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life

Read More
Priscilla V -
January 16, 2012
A:

Hi John,

Thank you for submitting a question to Manage My Life.

There are no known issues with this control panel or this dishwasher that I am aware of. I recommend checking the incoming voltage and ensuring that the wiring connections are good.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
January 17, 2012
A:

Where can I get a wiring diagram for this dishwasher. Also a troubleshooting manual. It seems that there is a white part clipped to the side of the plastic piece that holds the electronic control. It has 110 volts across it and seems like some kind of resister. I need a procedure to test it.

Read More
john -
January 18, 2012
A:

John, From your description I think the part you are talking about is the thermal fuse (see image below). I am also including a video below that demonstrates testing a thermal fuse. The thermal fuses in the video may not look exactly like yours, but the testing procedure is the same. The wiring diagram included with the images gives you the testing information for the touchpad buttons. I hope this is helpful. Check the things I have covered here, and if I may be of further assistance please reply to this post. Landell

Read More
Landell -
Sears Technician
January 19, 2012
See more answers
Q:

Dishwasher Not working

A:

I know how fast dirty dishes can gather and it is important to have a good working dishwasher in the home. While you are waiting for an expert answer, I did manage to find a link that describes a similar problem to the one that you are having. I hope my link is useful.

Read More
Joseph P. -
January 15, 2011
A:

I suspect that the clean light is blinking 7 times then pausing and repeating that pattern. This indicates that a problem was detected in the water heating circuit. I recommend that you examine the heating element in the bottom of the tub for damage. If you see no apparent problem, then you can reset the control board by placing the dishwasher in the diagnostic test mode. Press these keys in this order to start the diagnostic test mode: HEATED DRY -- NORMAL WASH -- HEATED DRY -- NORMAL WASH. This key dance needs to be completed rather quickly once it is started (within 5 seconds). Once this routine is completed properly, the dishwasher should begin the diagnostic test cycle. All of the console lights will turn on and then go off. The dishwasher will step through a brief test cycle to check all of the components (including the heating system). After this test cycle is completed, the control should be reset so that you can start a new cycle. You may be able to continue using the dishwasher after resetting the control in this manner. If the dishwasher works properly, I recommend that you continue to monitor it for problems for the next few uses. If you continue to see the blinking clean light fault code return, I recommend that you have the dishwasher serviced by a technician. Here is a link for the Sears Service website: Sears Home Services .

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
January 17, 2011
A:

Thank you so much and I will try your suggestions tonight.

Read More
Pam -
November 10, 2011
A:

Let us know how this turns out if possible. Thanks.

Read More
Lyle W -
Sears Technician
November 10, 2011
See more answers
Q:

Why is the clean light on my dishwasher flashing and preventing the dishwasher from operating?

A:

I will have to assume the "Clean" light is flashing 7 times pausing and constantly repeating to flash 7 times. If this assumption is correct; the flashing clean light is an indication of a heater detection fault. See image below for the possible failures causing the "Clean" light to flash. The error code can be cleared by pressing Heated dry, Normal, Heated dry and Normal in this sequence and allow the dishwasher to run for 2 minutes and then press "Cancel/Drain" and allow the dishwasher to drain. The dishwasher will operate normally again unless it does not detect an increase in water temperature again during the first 8 minutes of the main wash. If continues to flash the "Clean" light, the heater circuit will need to be checked including the heating element and the neutral door switch operation.

I recommend calling a servicing technician to diagnose and repair your dishwasher if the "Clean" light continues to flash again after resetting the control.

Read More
Joey S -
Sears Technician
January 18, 2010
A:

My dishwasher does not have a heated dry button. It has smart wash, antibacterial, pots/pans, normal wash, china/ gentle, quick rinse, hi temp scrub, sani rinse, air dry, delay hours, cancel/drain and start.

Read More
melissa -
February 08, 2011
See more answers

Top Parts