Model #66517033403 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

The dishwasher does not fill with water. It will rinse and drain. Could this be caused by a failed inlet water solenoid valve? How to verify solenoid failed? 66517033403 Kenmore Dishwasher

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore dishwasher.

From the information you have provided above, I can understand the frustration of having your dishwasher malfunction, after researching model number 665.17033403. when the dishwasher does not fill the most common part to fail would be the inlet valve. There’s a good chance this will need to be replaced. Below I will link some information on how to test the valve. The part number for the valve is W10158389. Also make sure the door is closing properly, if the door is not closed correct it won’t allow the water to enter the machine.

Click here.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
June 22, 2015
Q:

Thumping Noise After Run 66517033403 Kenmore Dishwasher

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dishwasher. Upon researching model 66517033403; based on the description provided, it sounds like the problem is water hammering of the pipes.  Water hammering can be caused a by a dishwasher when the machine water valve closes and the appliance is demanding more water than the pipes in your home can safely handle. Water hammer is discovered by hearing the thumping noise repeatedly. This problem is not a defect of the unit it’s a condition that can happen depending on the circumstances with an appliance and the water pressure from your home, that eventually affects the dishwasher and the pipes in your home.  If the problem is due to water hammering I would recommend getting plumber to take a look at the problem to see what can be done to help the appliance work with the water pressure present.

I trust this information will help you, have a great day.

Read More
CarlosZ -
Sears Technician
February 22, 2015
Q:

Upper spray arm slow 66517033403 Kenmore Dishwasher

A:

Thank you for choosing sears I would be happy to help you with your dishwasher. Upon researching model66517033403; you can try manually spinning the spray arm while the unit is off, If you feel resistance or it won’t turn freely then there may be some debris accumulated. You can remove the spray arm and clean it to remove any debris causing the problem. Make sure that the water tube that brings the water to the spray arm is not broken causing the water pressure decrease before it gets to the spray arm. In case the problem still persist, then the water valve may have failed not allowing the sufficient water pressure to get to the spray arms causing it to spin slowly.

I trust this information will help you, have a great day.

Read More
CarlosZ -
Sears Technician
January 08, 2015

Top Parts