Model #66517014401 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

the clean light keep blinking 66517014401 Kenmore Dishwasher

Q:

KENMORE DISHWASHER; SKIPS THE HEATED DRY CYCLE, HEATING ELEMENT HAS BEEN REPLACED 2 WEEKS AGO, WASHER WORKED FINE FOR 6 WEEKS NOW THIS PROBLEM.

A:

Providing a model number to your question will definitely help an expert better your search. If you would like to reply to this thread with a model number I would be more than happy to assist you. Have a nice day.

Read More
Alina F. -
January 30, 2011
A:

kenmore model#665.17014401

Read More
pam -
January 31, 2011
A:

Thank you for your question and I understand your concern. If the heater comes on and works in the first 8 minutes of the main wash then it should come on during the dry cycle unless "Heated Dry" has not be selected. I must assume that the "HEATED DRY" LED is lit on the Heated Dry button indicating that heated dry is selected. If the Heated Dry light is not lit, then the heated dry was not selected or it did accept the command. If the control will not accept "Heated Dry" then it may have console failure.

If the heating element was not working at all, the dishwasher would most likely at some point in time stop operating and begin flashing the "Clean" light and the control would have to be reset in order for the dishwasher to operate again. If the "Clean" light starts to flash again after resetting the control and starting another cycle, the failure could be the High Limit thermostat, control board, loose wiring connection, lack of water or a faulty heating element. I recommend calling a service technician to diagnose and repair your dishwasher.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 01, 2011
See more answers
Q:

Kenmore dishwasher does not fill with water

A:

I understand how frustrating it can be when your dishwasher is not working properly because then you have dirty dishes. I found a question in Manage My Life under the Answers button that was similar to the one you asked. I think this information will be very helpful to you. I attached the link below. I hope this helps!!!!!

Read More
Raquel F -
July 27, 2010
A:

Check the water supply shut-off valve to make sure that it is fully open. You can shut off the breaker for the dishwasher and pull it out to verify that the water supply is good if you hear the solenoid water fill valve buzzing when the dishwasher should be filling. Here is a link for the installation guide that will help you safely pull the dishwasher out from under the counter: Installation Instructions . Reverse the installation steps to access the fill line. With the water supply shut off, remove the water fill line from the inlet water valve assembly and place the end of the line in a container. Briefly turn on the water supply to check for proper pressure and flow. If the water pressure or flow is inadequate (or non-existent) then a plumber will likely need to fix this dishwasher water supply problem.

If the water supply is okay and the solenoid water fill valve is buzzing in the fill portion of the cycle then you will likely need to replace the fill valve assembly (part 8531670) You can order this part from the Sears PartsDirect website. Be sure that you shut off the breaker before accessing internal components when you replace this valve.

If the solenoid water fill valve is not buzzing in the fill portion of the cycle then this failure could be caused by a failed water valve, bad float switch, failed control board or a wiring failure in the circuit. A technician will normally need to diagnose and repair this type of failure. Here is a link for the Sears Service website: Sears Home Services .

If you want to try and resolve this final issue yourself, you can shut off the breaker and check the wiring connections on the control board, float switch and the solenoid water fill valve. I provided the wiring diagram for your dishwasher in the image below with the fill circuit traced in brown. If you are able to find a loose or failed wiring connection, you may be able to fix this problem yourself. If you do not find a loose wiring connection then a technician will need to check the circuit to see if the control board is supplying voltage to the valve. I don’t recommend that you attempt live voltage checks yourself.

Read More
Lyle W -
Sears Technician
July 29, 2010
A:

Thanks for you comments. One more detail. I lifted the float switch (the part that looks like a hat() once, reinserted back into its hole and then spun it. I then closed the door and pushed start. It did fill with water and continued its cycle. My guess it did not fill the next time it needed to fill in the cycle because the door was still dirty when the load was finished. Today I tried the lift the float trick several times and it did not work. Does this help us know that it is a bad float switch. I believe I have looked at the float switch diagram at Sear Parts Direct and if I'm looking at the right thing it does not look like there is much there (I did not see a switch persay). Thanks for your help.

Read More
WillOwl -
July 29, 2010
See more answers

Top Parts