Model #66516999400 KENMORE Dishwasher

  • Frame And Console Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Tub Assembly Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Dishrack Parts And Optional Parts Not Included
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Removing front panel of Kenmore Dishwasher (Model: 66516999400)

A:

Replacing the front panel on your dishwasher may seem like a difficult task without the proper instructions.  While you are waiting for an expert to respond, I have added a helpful link (click here) that may provide information to assist you with your question.

Read More
Yadira B -
July 18, 2013
A:

Thanks Yadira.

Read More
Mark -
July 19, 2013
A:

Thank you for choosing ManageMyLife.com. I understand how important it is to be able to replace the panel especially if you want to change the look of your kitchen. I have included instructions below on how to replace your dishwasher door panel.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Disconnect the power from the dishwasher by turning the circuit breaker off at the home electrical panel.

2. Open the dishwasher door completely. Remove the eight screws that are located on the side panel of the door using a screwdriver.

3. Close the dishwasher door while holding your hand flat against the outer door.

4. Lean the top of the front panel away from the dishwasher. Maintain a hold on the front panel door so that it does not just fall off, possibly breaking control wires.

5. Lift the front panel up and away from the dishwasher. Make sure that no wires become snagged in the process. Be especially careful near the control panel.

6. Insert the new front panel into the bottom rail of the dishwasher door. Push the front panel all the way flush with the dishwasher door.

7. Hold the front panel in place with one hand while opening the entire dishwasher door.

8. Insert screws into the four side corners while still holding the front panel flush with the door. Once the screws are in place, tighten them down with a screwdriver, and let go of the outer door panel.

9. Secure the inner door and front panel by reattaching the remaining securing screws.

10. Close the dishwasher door and turn the circuit breaker back on to power the dishwasher.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.
Black Door Panel for Kenmore Dishwasher Model # 66516999400
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using ManageMyLife.com.

Read More
Desirea -
Sears Technician
July 21, 2013
A:

Thank you Desirea!

Read More
Mark -
July 22, 2013
See more answers
Q:

Hello I have a Kenmore Ultra Dishwasher, Quiet Guard 2, model number 665.16999400, I want to know what the DBA sound level is on this machine?

A:

To find out what the DBA sound level is for the Kenmore dishwasher, it will take some research from our experts. Thank you for your patience while the experts get the answer to your specific question. I am providing a link that may be helpful.

Read More
Anna T -
April 03, 2012
A:

That particular model did not have a specific decibel rating. Based on the type of motor that is has and the sound insulation in the unit, the decibel level would likely be around 58 db. You should be able to use this sound level for comparison to new models.

Read More
Fred M -
Sears Technician
April 04, 2012
See more answers
Q:

kenmore fuse

A:

Having to find the proper parts for your Dishwasher Can be frustrating as well challenging. While you are waiting for a detailed reply from an expert I recommend visiting the Sears parts direct website were you can view a full parts diagram for your Dishwasher. I have added the link below. Hope this helps!

Read More
Priscilla V -
February 29, 2012
A:

Thank you for your question and I understand your concern.

Your model dishwasher does not have a fuse. I added the wiring diagram of your model in the image below. If your dishwasher will not operate at all, I suggest taking a look at the wiring connections where the power supply connects inside the electrical junction box and then the door switches. It's not uncommon to find a burnt wire nut indicating a loose and bad connection. NOTE: Disconnect the power supply from the dishwasher by flipping the house circuit breaker off dedicated for the dishwasher circuit before disconnecting the wires. If the wire connections look okay, the voltage supply should be measure across the black and white wires. NOTE: I do not recommend checking the voltage supply unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your dishwasher.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
February 29, 2012
See more answers

Top Parts