Model #66516689000 KENMORE Dishwasher

  • Frame And Console
    3 Results
  • Inner Door
    3 Results
  • Tub Assembly
    3 Results
  • Pump And Motor
    3 Results
  • Upper Dishrack And Water Feed
    3 Results
  • Lower Dishwasher
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Drain problem 66516689000 Kenmore Dishwasher

A:

There is a known fix for that problem that works almost all of the time. It is a fairly easy repair. Here is a link for that fix:  http://www.managemylife.com/mmh/questions/215084-check-clog-dishwasher-drain-pump

 

If you examine that check valve as shown in that previous answer and find no problems, let us know and we will assist you further. 

Read More
Lyle W -
Sears Technician
November 22, 2013
Q:

Water not running in

A:

I understand how frustrating this can be. While you are waiting on an expert to answer your question, I suggest you to verify your model number and attach complete model number to this thread so you can get a better answer from the experts. Hope this helps!

Read More
Dezeray -
February 19, 2013
A:

I have type 279-2 or under/after the motor specs reads E71195 there is a serial number 17829000 and stock number fm21250022

Read More
judith -
February 19, 2013
A:

this looks to be the correct manual Find parts for your model number at Sears PartsDirect: 3385344, 66516684000, 66516682000, 66515682000, 66516689000, 66515684000, 66515689000 hide

Read More
judith -
February 19, 2013
A:

Thanks for the information about the portable dishwasher; sorry you are having a problem with water entering. Unfortunately the model number you provided is not correct, so I will only be able to provide a general answer. First be sure the faucet attachment is properly on the water supply and the water is turned on. The door must be closed completely and locked.   Look Inside the dishwasher tub. (Front right on most models) you will see a float assembly. Be sure this float does not have something lodged under it, as this will keep the water from coming into the tub. If you are hearing a buzzing sound when water should be coming into the tub, then the inlet valve is being activated by the water level switch and the timer.  In this case no water coming in would mean a bad inlet valve or not water supply to the valve.  I hope this helps, if you need additional assistance please reply with a complete model number off the dishwasher and added details and I will be happy to respond.Ron H. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services

Read More
Ron H -
Sears Technician
February 20, 2013
See more answers
Q:

Dishwasher not filling with water

A:

I'm sorry to hear that you are having some difficulties with your dishwasher, water not entering can really keep you from getting the dishes cleaned and I will be happy to help. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Joseph P. -
November 19, 2011
A:

Thank you for your question and I understand your concern.

Your dishwasher has a pressure switch located under the dishwasher. If the pressure switch trips due to a faulty pump, it will cause the dishwasher to pump the water out. You can disconnect the wires from the pressure switch and then operate the dishwasher and see if continues to pump water out. If it doesn't pump out water immediately then you could leave the wires disconnected and your dishwasher will likely clean as well as it did before; otherwise you would need to reconnect the pressure switch wires and replace the pump assembly. If you leave the wires disconnected be sure to tape the ends so that they won't possibly short to ground. NOTE: Disconnect the power supply from the dishwasher before removing the lower access panel and disconnecting the wires from the pressure switch. If you disconnect the pressure switch hose and water and debris is found, this will also indicate a pump failure.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
November 21, 2011
See more answers

Top Parts