Model #66516369300 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Install a Part Kenmore dishwasher 665.16369300... how to install dispenser #8558129

A:

When it comes to getting the Kenmore dishwasher dispenser installed and working, you can depend on managemylife.com experts. The information in the link provided below should help you with the installation. An expert will respond with additional information within two business days, usually sooner.

Read More
Anna T -
February 08, 2013
A:

Thank you for your question and I understand your concern.

 

 I added a couple of images below with the procedure of separating the inner door panel from the outer and how to replace the dispenser assembly.

NOTE: Disconnect the dishwasher from the power supply before servicing. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

 

Read More
Joey S -
Sears Technician
February 08, 2013
See more answers
Q:

what is decimal level for a dishwasher 665.16369300

A:

The ManageMyLife website is a great place to find answers to questions that need qualified and insightful responses. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner. I have provided an excellent article and the link to Sears.com where you can find the quietest dishwasher available at Sears. A Sears associate will be happy to answer your questions.

Read More
James -
May 12, 2012
A:

This is an older model and the decibel rating for this model is not listed in the tech specifications; however the average for this model type is 58 to 60 dB. Some newer dishwashers can be 51db or lower. I hope this helps your shopping.

Read More
Fred M -
Sears Technician
May 12, 2012
See more answers
Q:

Can I check incoming water pressure or replace motor assembly or motor impeller myself?

A:

You can likely check these issues yourself. To check the incoming water pressure, you can first check the water level inside the tub of the dishwasher after it finishes filling and before it starts spraying. Start a cycle and allow the dishwasher to fill. After the filling stops and before the spray starts, crack open the dishwasher door. Open the door fully and observe the water level in the bottom of the tub. The water level should be within 1/4" to just touching the bottom of the heating element in the bottom of the tub. If it is too low, try manually adding some hot water to raise it to the properly level with a bucket or container. If the dishwasher washes properly with the proper amount of water then this is the issue that is causing your problem.

To further analyze a water fill problem, you would need to use your installation guide to pull the dishwasher out and check the water pressure and flow coming from the fill line. Here is a link for the installation guide for your dishwasher: Installation Instructions . The basic procedure for pulling the dishwasher out to check the fill line and inlet water valve includes these steps:

  1. Shut off the breaker to the dishwasher to disconnect electrical power.
  2. Shut off the inlet water supply valve for the dishwasher. This cut-off valve is normally under your sink.
  3. Remove the screws from the brackets that secure the dishwasher to the counter.
  4. Remove the lower access panel (see page 13 in the installation instructions).
  5. Carefully pull the dishwasher out from under the counter far enough to access the water line and inlet water valve assembly.
With the dishwasher pulled out and the lower access panel removed, you can pull the water supply line off and place the end of it in a pan or container. Briefly turn on the cut-off valve to check the water pressure and flow from the water supply line. If it is inadequate, you will need to have a plumber resolve this issue. If the water supply pressure and flow is okay, check the screen on the inlet water supply valve for debris or hard water deposits that could be inhibiting water flow. If the screen is okay, you may need to replace the valve or the water inlet assembly. You can view these parts (and order them if necessary) on the Sears PartsDirect website. Use your full model number (665.16369300) to access the correct parts listing and order parts.

If the dishwasher is filling properly, I recommend that you check the water temperature as shown on page 12 of your owner's manual. Here is a link for your owner's manual in case you need it: Owner's Manual .

If water temperature and level are okay, check your spray arms for cracks or splits. Check the holes in the spray arms for clogs or deposits.

If all of the above issues are okay, you could have a problem in the sump area that is causing your washing problem. Shut off the breaker to the dishwasher and remove the upper and lower racks (page 9 in your owner's manual shows how to remove the upper rack). Follow the steps shown in the image below to access the chopper blade area and check valve in your sump. NOTE: Your dishwasher is slightly different than the one shown below. Your inner feed tube is likely secured to the dishwasher tub with screws instead of clip. The basic procedure is the same even though you may find slight differences in your dishwasher. If you access the chopper blade area of the sump, you may find a foreign object or clog in this area that is inhibiting water flow in the sump. Removing the obstruction in the sump may fix your problem.

These tips may help you resolve your dishwasher problem. If the pump does have a broken impeller, I recommend that you have a service technician repair the dishwasher. Replacing the sump and motor assembly is not difficult but it involves working with water seals at the bottom of the dishwasher. If the water seals leak, it could ruin counters and cause other damage.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
November 21, 2009

Top Parts