Model #66516052402 KENMORE ELITE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

I need a silverware basket for my dishwasher but can't find a part number. 66516052402 Kenmore Elite Dishwasher

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your dishwasher. Upon researching model 66516052402; I have posted a link of the silverware basket part# to view the link click here.

 

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
August 16, 2015
Q:

replace kenmore dishwasher door hinges

A:

I did some research on the unit and I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Joseph P. -
August 25, 2012
A:

Thank you for your question and I understand your concern.

I was not able to locate any written instructions or video for replacing the door hinges. The hinges are held in place with a couple of screws. If you separate the inner door panel from the outer door panel should have access to the left and right hand hinges. I added images below with some instructions on how to remove the outer door panel and how to route the door springs and the lanyards. Disconnect the power supply from the dishwasher before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
August 27, 2012
A:

Thanks to Joey S. I did the repair today and everything worked out well. The diagrams were especially helpful. Perhaps even more helpful was the comment that indicated an ordinary human should be able to accomplish the repair. Thanks again.

Read More
John -
September 13, 2012
See more answers
Q:

Why won't my Kenmore dishwasher work?

A:

If it is as easy as changing a fuse on the Kenmore dishwasher, our experts will know. I am providing a few links that may be helpful in diagnosing the problem with the dishwasher. An expert will be along with additional information.

Read More
Anna T -
May 29, 2012
A:

Thank you for submitting your answer and I will be happy to assist you with your dishwasher. If you have a volt/ohms meter and are comfortable working around live electricity I can give you a few checks that will help you diagnose the problem. You're wiring diagram is provided in the first image below. First, check the V.A.C. (Voltage Alternating Current) into the dishwasher. Remove the toe panel and locate the terminal block (where the household wiring is connected to the dishwasher). While grasping the insulated portion of the volt/ohms meter probes ( never touch the metal conductor during testing ) place one probe on each of the wires. The dishwasher needs to have 120 vac on the black wire with the white stripe and the tan wire. You will need to place one meter lead on the black wire with the white tracer and one lead on the white wire. Then place one meter lead on the tan wire leaving the other meter lead on the white wire. NOTE : You must have the door switch energize when checking the voltage on the tan wire. It only has voltage present when the door is closed. It must have 120 vac on both the black wire with the white stripe and the TAN wire. If you have the correct voltage on both wires, most likely the failure is the interface board or a bad connection between the control board and the touch panel board on P1 connector. If you do not have voltage on Black wire with the white stripe, check the thermal fuse. The thermal fuse (key #6) should give you an ohms reading of zero. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with out Sears Home Services team. Please reply back to this thread if you need more assistance. I hope this helps. Thank you for choosing Manage My Life.

Read More
Tykara -
Sears Technician
May 31, 2012
See more answers

Top Parts