Model #66515955791 KENMORE Dishwasher

  • Frame And Console
    3 Results
  • Inner Door
    3 Results
  • Tub Assembly
    3 Results
  • Pump And Motor
    3 Results
  • Upper Dishrack And Water Feed
    3 Results
  • Lower Dishrack
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Is the screw 3371152 on Kenmore washer 66515955791 impelar a left or right hand thread?

A:

I have provided you an image below of how to replace the impeller of your dishwasher. Hold the impeller and turn the screw counter clockwise to remove the screw. Your dishwasher making noise when running most likely there is something caught in the macerator screen. Check the macerator blade it may be bent. After you have completed the repair check under the dishwasher for leaks. Any parts you may need can be ordered from this link. Sears Parts Direct

Read More
Mark T Personal Solutions Manager -
Sears Technician
December 09, 2009
A:

Thanks guys, this is what I needed help with. However, I'm having issues actually removing the screw. I got it loosened, but it just won't come out the rest of the way. I'm holding the impeller and turning counter clockwise.......but it just kind of spins. Any suggestions?

Read More
James -
September 13, 2012
See more answers
Q:

Kenmore ultra wash 665.15955791

A:

I understand your concern with the dishwasher. Getting the dishwasher so that your dishes will be nice and clean is important. I did some research on www.managemylife.com. I am adding the links below to help you with your question while you wait for your expert response.

Read More
Marc H -
March 11, 2012
A:

This dishwasher has a thermal fuse but if that fuse was blown then the heater would not work. That fuse would not affect the water fill function in this dishwasher.

There is a possibility that the dishwasher is stuck in the sales demo mode. You can use the procedure shown in the first image below to exit that mode.

A problem with the overfill float switch, the control or the inlet water fill valve assembly could be causing your failure. A wiring problem or a water supply failure could also prevent the dishwasher from filling. I recommend that you verify that the water supply cut-off valve for the dishwasher is fully open. Check the overfill float in the bottom of the tub to see if it is stuck in the "up" position. Listen for a buzz from that water valve when the dishwasher should be filling at the start of the cycle. If you do not hear that fill valve buzzing then I recommend that you shut off the house circuit breaker for the dishwasher and check the circuit that is traced in red on the wiring diagram in the second image below. You could have a loose wiring connection on the control board, the float valve or the solenoid inlet water valve assembly. If that water valve is buzzing, then you either have a water supply problem or a failed inlet water valve assembly.

You can order parts from the Sears PartsDirect website if needed.

These initial tips may help you determine the cause of your fill problem. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 13, 2012
A:

Here are links to the overfill float switch and the inlet water fill valve on SearsPartsDirect.com...

Read More
Parts Expert -
March 13, 2012
See more answers
Q:

I have dishwasher 66515955791. The pump runs, but does not remove water at the end. Looking for parts reccomendation. All drains are clear.

A:

I'm sorry about the difficulties that you are experiencing with your dishwasher. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. If you would like assistance from a qualified technician I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
January 04, 2011
A:

This type of problem is normally caused by a clogged check valve assembly at the bottom of the dishwasher. You may not need to replace any parts. I recommend that you examine the check valve as described below.

The first image shows the drain hose connected to the check valve. I recommend that you shut off the breaker to the dishwasher and remove the bottom front access panel to access this end of the drain hose. Use a shallow pan to catch any residual water that will drain out of the dishwasher when you remove this hose.

The second image shows the check valve with the drain hose removed. Unscrew the check valve and remove it to check the flapper valve as shown in the third image.

If you find no problems with the check valve, I recommend that you check the opening of the sump where the check valve screws in for a clog or restriction. If you need to access the sump area from inside the dishwasher, you can follow the steps in the 4th image below.

If you find any damaged or broken components during this examination, you can order parts from the Sears PartsDirect website.

These tips may help you resolve this drain issue in the dishwasher. If you need more help, submit additional details and we will try to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 06, 2011
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
January 06, 2011
A:

Thanks. I will try this

Read More
Steve B -
January 12, 2011
A:

I'm positive that Lyle W was right on. I took the hose off and water just barely dripped out. I removed the check valve and it was choked shut with pieces of plastic. I then managed to break the float (assembly 3376397) by trying to pull it up and off to see if it had debris in it and broke the plastic arm. I tried to test run the dishwasher and it will not fill with water. I take it the broken float assembly is preventing this? How does it get installed? Thanks so much for your time.

Read More
Anonymous -
January 13, 2011
A:

I am glad that you found the problem with the drain system on the dishwasher. Sorry to hear about your problem with filling. I provided information about the float switch in the image below. A problem with the float switch can prevent the dishwasher from filling. The information shown below should help you see how the component works. If the switch fails in the "up" position then it will prevent the dishwasher from filling. If you repair the float switch and the dishwasher still won't fill, then you could have a problem with the fill valve, the wiring or the control board. If the valve is buzzing when the dishwasher is in the fill mode then your failure is likely in the fill valve or the water supply line. I hope that these tips help. Reply with additional details if you need more assistance.

Read More
Lyle W -
Sears Technician
January 13, 2011
See more answers

Top Parts