Model #66515894100 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dishwasher tub is wet after drying cycle is complete causing mold to grow. 665.15894100

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your dishwasher. Upon researching model665.15894100; the vent does open during the drying cycle. If it’s not opening to let out steam during the drying cycle it could need to be replaced.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
November 05, 2014
Q:

Not finishing cycle 66515894100 Kenmore Undercounter dishwasher

A:

I can understand your concern when the Kenmore dishwasher will not run a full cycle. The link provided below has some information that may be helpful. An expert will respond with additional information within two business days.

Read More
Anna T -
February 15, 2013
A:

Thank You for submitting you question to ManageMyLife.com

I can understand how frustrating it can be when you dishwasher doesn't want to finish the cycle. Base on the model number you provided. I'm showin the Electronic Control Board would need to be replaced. I have included a link to our PartsDirect webpage where you can purchase the part. Please click the blue link below.

Electronic Control Board for Model 665.15894100

Read More
Desirea -
Sears Technician
February 15, 2013
See more answers
Q:

How do I install a Kenmore Dishwasher heating element?

A:

Hello, I think it is great to be able to install your own parts on your appliances. I researched your question and found someone asked a question similar to yours. Here is what was posted by an expert. I have provided the link below. I hope this helps!

Read More
Jacqueline S -
July 16, 2010
A:

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

In order to install a new heating element in your dishwasher you will need to pull it out from under the cabinet. First, disconnect power & turn off the water supply to the dishwasher. Open the door & remove the mounting screws going up into the countertop. Remove the lower inspection panel. Raise the leveling legs to lower the unit to make it easier to slide out; be sure to protect the floor. After sliding the unit out you will be able to access the heater nuts with the proper tool & replace the element. Remember to disconnect power before attempting access.

I do not recommend running the dishwasher until the element is replaced.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
biker dave -
Sears Technician
July 19, 2010
See more answers
Q:

What is the part number of the black seal that slides into the tub housing for a 665.15894100 Kenmore dishwasher. The length is approx 66 inches?

A:

From the description you give I believe you are referring to the door gasket.

The 8268888 door gasket is available from the following link: Sears PartsDirect for about $55 dollars.

I hope this is the information you wanted but submit another question with any additional details for further assistance.

Read More
Fred M -
Sears Technician
May 25, 2010
Q:

How do I remove the top dishwasher rack?

A:

There are stops at the front of the wheel tracks for the top rack that will need to be removed. Once you remove the stops, you can pull the top rack completely out of the dishwasher. It appears that this dishwasher has the stops where you need to pull the tab out and slide the stop to the open side of the track to remove it.

Once you get the rack removed, you can access the upper feed tube where the spinner is installed. Remove any remaining components from the previous spinner. The new spinner that you receive may be slightly different than the original one. Use the hard water provided to snap the new spinner in place on the upper feed tube. The feed tube should be flexible enough for you to bend it down so you can install the new spinner.

Read More
Lyle W -
Sears Technician
April 07, 2010
Q:

How do I repair a hole that was burnt through the bottom of my dishwasher tub?

A:

Your dishwasher tub has a limited lifetime warranty. A Sears’s technician would have to come out and determine the exact cause of the failure. The tub might be replaced under warranty depending on the diagnoses; however you would be responsible for the labor.

I recommend calling Sears at 1-800-469-4663 to set up an appointment to have a technician come out.

Read More
Joey S -
Sears Technician

Top Parts