Model #66513922K010 KENMORE ELITE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel And Latch Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Fill, Drain And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump, Washarm And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

Eco light display will not shut off

A:

I'm sorry that you are having some difficulties with yourKenmore Dishwasher. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. Remember that your expert can walk you through a repair like this and even assist you on ordering any required parts. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com.

Read More
James -
August 02, 2011
A:

Your description points to a bad user interface control panel in the dishwasher since you cannot select other cycles besides the ECO cycle. If you can select other cycles but the light on that cycle just stays lit, it can indicate that you have a bad electronic control board in the dishwasher. If your dishwasher is still under warranty, I recommend that you call Sears at 1-800-469-4663 (1-800-4MY-HOME) and have the dishwasher repaired.

If the dishwasher is not under warranty, reply with additional details and we will assist you further.

You can schedule service for the dishwasher at this website if it is not still under the warranty: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 04, 2011
A:

My Kenmore Elite dishwasher 665.1392 model is having the same problem. Two reports in such a short period of time indicates a defect that should be looked in to, not just repaired. How do we get this escalated to a review and possible 'recall'?

Read More
Kevin -
January 04, 2012
A:

Hello Kevin. I agree that 2 reports of this problem within a short period of time is a cause for concern. I have forwarded information on this problem to our product engineer for the dishwashers. A full model number and serial number of your dishwasher may help with the communication and investigation of that problem as a possible widespread defect. If you get a chance, reply back with that information. If the dishwasher is still under warranty, I recommend that you have it serviced. If the dishwasher is no longer under warranty and you want to fix this problem yourself, let us know and we will assist you further with troubleshooting and technical help.

Read More
Lyle W -
Sears Technician
January 05, 2012
A:

Thanks for the speedy response. Mod# 665.13923K010 Ser# F03903872 All other lights/functions work fine. It is no longer under warranty and I would be interested in fixing it myself if Sears is not willing to step up to the plate.

Read More
Kevin -
January 05, 2012
A:

Since the dishwasher is not under warranty, the repair will not be covered. I do not see any widespread common problems or recalls on that dishwasher at this time. You will normally need to replace the control panel to fix this problem. You can order that part from the Sears PartsDirect.com website (see link below). That control panel is listed in several colors. You can order the color that you need. Shut off the house circuit breaker for the dishwasher before accessing internal components and replacing that panel. You can remove screws from the top of the inner door panel to release that control keypad. Reply with additional details if you need more help with that repair. There is a chance that you will also need to replace that electronic control board in the console if you replace that key panel and still have problems programming the dishwasher. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
January 06, 2012
A:

I have a Kenmore Elite dishwasher. Model # 665.13922K010, SN F03605218. I have the same problem with the Eco light staying dimly light all the time. I ran the dishwasher two days ago and the light was not on. I noticed that the light was on this morning. I am single and live alone so I know that no one touched the button. If I touch it the light goes bright like it does when you select it. If I touch cancel it goes dim again, but does not turn off. I can select any other functions and the dishwasher appears to work normally except for the fact that the eco light stays dimly light. I bought this dishwasher in Feb of 2011 so it is 15 months old and obviously out of warranty. What do I need to do to get this fixed? Has this been identified as a defect? Thanks for your help.

Read More
Jeff -
May 20, 2012
A:

That type of problem is often caused by a problem with the control board and/or the user interface console. There is a chance that you have some humid air or moisture getting into that console through the air vent area. You can shut off the house circuit breaker for the dishwasher and check the seals on that vent. Let us know if you need help accessing that area or checking those vents. I will check again for any common problems with that dishwasher.

Read More
Lyle W -
Sears Technician
May 21, 2012
A:

Well it seems like there might be some kind of short causing the light to stay on. I checked the owners manual and it doesn't say how to get to the seal. Can you tell me how to check the seal to see if it is bad?

Read More
Jeff -
May 21, 2012
A:

Hello Jeff. I added an image below that shows how to access the seals on that type of vent. Your dishwasher will be slightly different than the one shown below but the basic procedure is the same. Be sure that you shut off the house circuit breaker for the dishwasher before accessing that area. This information may help you check that vent and the seal. A leak in that vent area can cause humidity and moisture to enter the control area. That could be causing the short in that board or console and cause the Eco light to stay on. That board and console may still be okay. It will probably work properly once the control dries out. If you find and fix a problem with that vent seal, then you may be able to prevent any further problems without replacing any parts. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
May 22, 2012
See more answers
Q:

I have blue flashing light, 4 times on complete cycle. When I open door it beeps. 66513922K010 Kenmore Elite Undercounter dishwasher

Q:

Kenmore dishwasher heating element won't shut off 665.13922k010

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help you with your dishwasher. Upon researching model 11029822800; I understand your concern.
If the heating element is staying ON continuously then I must assume the control board has stuck heater relay. The electronic control board may need to be replaced if the relay is stuck on this control board causing the element to stay on continuously. I have posted a link of electronic control board to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
June 08, 2015

Top Parts