Model #66513899K800 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Send directions to install a W102224456 detergent dispenser in a Kenmore Ultra Wash dishwasher, model 665.13899K800

A:

 Hi,

Thanks for contacting  ManageMyLife.  I understand how frustrating it is having trouble with your appliance.

The dispenser is replaced by killing power to the dishwasher and removing the screws from in inner door panel and separating the two.  You will need to remove the plastic vent screen and separate the door panels the get to the dispenser.  IMPORTANT, if your old dispenser has a small circuit board installed on it, take it out of the slot, being careful not to damage it and install it into the new dispenser.    

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
October 25, 2013
Q:

Missing part 66513899K800 Kenmore Dishwasher

A:

Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when needing a part for your dishwasher. I did look into the model number you have provided and I do not see a curved piece under the unit, due to the diagrams are all spread out. I would need more information on the part to see if I can locate you the part. We would need the height, length, color, function, etc to determine what part is missing.   I was able to locate the year of the unit, in which, is 2008. Once we have more of a description I will be able to search the part. If you are needing to look at the diagram you are able to at searspartsdirect.com when you are ready.

Thank you for your question. Have a great day.

Read More
Natasha12 -
Sears Technician
October 01, 2013
Q:

Broken Dishwasher

A:

I know how important it is to have a good working dishwasher in the home so that you can keep your dishes nice and clean. I am sorry for the inconvenience and I did manage to find a link with a similar question. I hope this helps with your research while you wait for your expert response. 

Read More
Joseph P. -
March 07, 2013
A:

I know that it can be very frustrating to have issues with your dishwasher. If the Normal LED light is blinking rapidly that generally indicates a stuck key or shorted circuit(s) in the key pad. It's possible to have shorted circuits or shorted connections on the control board that reads the keys too. Most likely it's going to need a console assembly w/active overlay. There is a Key Pad switch resistance check table on the tech sheet that will be needed to test the operation of the key switches. An ohm meter will be needed to make these checks.

I recommend calling a service technician to diagnose which one has failed unless you have a volt/ohm meter. I added an image with the "KEYSWITCH RESISTANCE CHECK TABLE" in order to be able to test all the keys.

Checking keyswitch contacts:

  • Unplug dishwasher or disconnect power.
  • Remove connector P1 from the control board. Using the table below that I added in an image, measure the resistance NOTE: The meter must be connected with the proper polarity. P1 connector is the keypad connection. The resistance reading should go from infinity (open circuit) down to a readable ohm level with the key button/switch pushed. The level may be different depending on your meter, since there is a diode in the circuit.
The resistance reading should go from infinity down to a readable ohm level. The level may be different depending on your meter, since there is a diode in the circuit. If available, you could use the “Diode Test” function of a digital meter, which will give a voltage of about 1.2 VDC during the test.
  • If any switches fail this test, replace the console panel/keypad assembly.
  • If all switches test OK, replace the machine control board.

I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
March 08, 2013
See more answers

Top Parts