Model #66513873K602 KENMORE PRO Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill, Drain, And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

Handle cap - not in parts list for model #66513873K602 66513873K602 Kenmore Pro Dishwasher

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

 I do apologize I am not seeing those caps for the end of your handles. I recommend calling 18004MYHOME and speaking with our customer care so they can submit a research to locate that part. They will be able to contact the manufacture to see if those caps are sold. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
June 22, 2015
Q:

Dead Dish Washer 66513873K602 Kenmore Pro Dishwasher

A:

My problem was the thermal fuse. What condition may cause the fuse to blow?

Read More
Marc -
February 15, 2014
Q:

My Kenmore Elite Dishwasher Model 665.13129K701 is not draining. What could be the reason?

A:

Having a Kenmore Elite Dishwasher that doesn't drain properly would have me going crazy, especially if the drain smells. There is different questions in Manage My Life under the Answers button that is similar to the one you asked. These questions will give you good advice, while waiting on an expert answer. I attached a link below that will give you a suggestion on what might be your issue. I hope this helps!!!!!!!!!

Read More
Raquel F -
October 04, 2010
A:

You could have a clog in your sink drain system or the drain line from the dishwasher that is causing this problem. If you have an air gap installed on the sink drain system, make sure that the air gap is not clogged. A failed drain check valve in the dishwasher would allow water to flow back into the dishwasher. A failed drain pump, a bad control board or a wiring failure could also cause this problem.

Here are some tips for checking some of these issues:

  • Make sure that the sink drain is flowing properly.

  • If you have an air gap installed, check that component to make sure that it is clear.

  • With the dishwasher off, pull the drain hose connection off of the garbage disposal (or sink drain if you don't have a garbage disposal installed). NOTE: Position a bucket under the drain hose when you pull it off to catch any residual water in the drain hose. Check the end of the hose for a clog or build-up of grease that could prevent the dishwasher from draining. Place the end of the drain hose in your bucket. Press the Cancel/Drain button to start the drain pump on the dishwasher. Check the water flow from the end of the drain hose.

  • If the flow from the hose is good, then I recommend that you test the drain check valve. With the dishwasher off, hold the drain hose up as high as possible and pour water through the end of the hose to see if the tub starts to fill with water. You may need to use a funnel to pour water through the drain hose. If the water flows into the tub then the drain hose with check valve (part W10137608) will need to be replaced. You can order this part from the Sears PartsDirect website. You can shut off the breaker and the water supply to the dishwasher. The installation guide will help you pull the dishwasher out from under to the counter to access the drain hose and replace it. Here is a link for the installation guide: Installation Instructions .

  • If the dishwasher won't drain into the bucket then you could still have a clog in the drain line. If the drain pump is running, you could have a failed drain pump. If the pump is not running then you could have a bad pump, a wiring failure or a defective electronic control board in the dishwasher. These failures will normally require a service technician. Here is a link for the Sears Service website in case you need it: Sears Home Services .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
October 05, 2010
A:

The drain hose does not seem to be clogged and the check valve seems to be working. I do not hear a pump running or trying to run when I press the Cancel/Drain button. Nothing happens for a couple minutes, then the light goes out and it is finished, but no water has been pumped. I siphoned the water from the dishwasher, then ran the quick rinse cycle. It seem to run through the cycle normally, but did not drain -- and again I could not hear the pump running or trying to run at the end of the cycle.

Read More
Anonymous -
October 05, 2010
A:

Since you don't hear the drain pump running, you could have a bad pump, a wiring failure or a defective control board. I recommend that you shut off the breaker to the dishwasher and access the control board in the console as shown in the image below. You can check the resistance through the drain pump circuit as shown below with a volt/ohm meter. If the resistance through that circuit is not between 15 and 19 ohms then you will likely need to replace the pump. You can rule out a wire harness problem by accessing the pump and checking the resistance directly at that component (with the electrical power still disconnected). I provided access information for the pump in the image below as well. If the resistance directly at the drain pump is okay, then you will need to check the wiring harness for continuity. Plug the pump back in and check the resistance through the brown wires that connect to pins P11-6 and P11-4. If the resistance through these wires is 15 to 19 ohms (cont)

Read More
Lyle W -
Sears Technician
October 05, 2010
A:

then you have an internal failure in the control board. These tips should help you determine the cause of your drain pump failure in the dishwasher. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
October 05, 2010
A:

My problem is very similar to the above (Kenmore Pro 665.13873k602). However, mine drains perfectly if i press the drain button. Does this eliminate the float switch?

Read More
T_Edsel -
August 05, 2013
A:

timedsel: If it drains all the water out when Cancel/Drain is pushed, it should also drain after the wash and rinse cycles. The float switch would prevent the dishwasher from filling with water and have nothing to do with it pumping the water out. Is the drain pump not coming on after the wash or rinse cycles are completed?

Read More
Joey S -
Sears Technician
August 06, 2013
A:

I'm not sure if it is coming on at the end of the cycle. That would be a long boring wait. I ran the "Fast Cycle" and there were suds in the bottom plus water over the heating element. We usually run the dishwasher just before bedtime and we don't open it until morning, so the suds thing might be happening every time but the suds dissolve overnight. It leaks at the bottom of the door only after you open the door. It drains quickly if you press the drain button. Control unit problem?

Read More
T_Edsel -
August 06, 2013
A:

timedsel: If the detergent is producing alot of suds after the wash cycle completes, the drain pump will not be able to pump out. Now, if the dishwasher sits long enough, the suds will break down to a liquid which will drain but if the water is oversuds when the dishwasher needs to drain, it will not pump out suds. Do not add any detergent and run a short cycle and see if it drains after each wash and rinse cycles.

Read More
Joey S -
Sears Technician
August 06, 2013
A:

ActuallyI did that first. I ran a different cycle (fast) just to see if that would change anything (it didn't ). Also, I tried turning off power at the breaker for 10 minutes. This ma or may not have anything to do with anything, but this dishwasher stops occasionally, soap pod intact. We were assuming we had something loaded improperly, we would rearrange run it again and it would run. But it wasn't like anything was blocking the spray arm. Never the less, it would run fine on the second try. How deep should the water be at the peak? The water is up to the track now (about 1.5" depending on where you measure).

Read More
T_Edsel -
August 06, 2013
See more answers

Top Parts