Model #66513793K601 KENMORE ELITE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Question and Answers

Q:

My kenmore dishwasher model # 66513793K601 circulates soapy water when none was put in. 66513793K601

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dishwasher and I do understand your frustration. Glad to help out. I'm looking at your model number 66513793K601 and from your description I would suspect that this is an issue with the detergent being used. I recommend running a cycle with a cleaner without dishes to try and clean and rinse out the tub and spray arms completely and try to determine if the soap is the problem. Here is a link that will help with the leaking problem. I do not believe the problems are associated. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
February 03, 2015
Q:

Diagnostic test 66513793K601 Kenmore Elite Dishwasher

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dishwasher is not working properly. 


PROBLEM: WON’T START AND START/RESUME KEY LED
FLASHES 3 TIMES WHEN START/RESUME KEY IS PRESSED:
Control programmed to not
start if it suspects door switch
is stuck closed. Control looks
for switch to open between
cycles.
? Customer didn’t open door
between cycles.
? Door switch contacts stuck
closed.
1. Open and close door and then
press Start/Resume key. Instruct
customer.
2. Unplug dishwasher or disconnect
power.
3. Measure resistance of door
switch contacts while checking
mechanical operation of latch
assembly

PROBLEM: WON’T RUN AND LED FOR START/RESUME
KEY IS BLINKING SLOWLY
By design, if the door is opened or power is interrupted
during a cycle, the user must
press the Start/Resume key to
resume operation.
 
The door must be latched for the Start/Resume key to work.
NOTE: For models with all
keys on top of the door, the
Start/Resume key can be
pressed with the door open
but the door must be latched
within 3 seconds.
Confirm door is closed properly
before pressing Start/Resume key.
Instruct customer; refer to Use &
Care manual.
Door switch not making
contact:
? Faulty or sloppy door latch
assembly (which can be
aggravated by high door
closure force keeping strike
plate from fully seating).
? Faulty door switch (high
resistance).
1. Unplug dishwasher or disconnect
power.
2. Measure resistance of door
switch contacts while checking
mechanical operation of latch
assembly. Confirm switches not
loose from assembly. Check strike
plate and door closure.
Loose connections between
door switches and pin 8 on
control (pin 4 on plastic tub
models only).
1. Unplug dishwasher or disconnect
power.
2. Check resistance of all harness
connections between door switches
and pin 8 of the control (pin 4 on
plastic tub models only).
Start/Resume key not
responding.
Faulty control.
1. Unplug dishwasher or disconnect
power.
2. Check/replace control.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
January 19, 2015
A:

Thank you. But the answer you ve given has nothing to do with my question. And just in case you think it does, I have already checked the door contact switch.

Read More
Merdad -
January 19, 2015
See more answers
Q:

What causes 3 successive buzzes on my 665.13793K601 Kenmore Elite dishwasher ?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
June 15, 2013
A:

Hello Mike. I am sorry to hear about this problem that you are having with your Kenmore Dishwasher Model 665.13793K601

 

Since the buzzing is occurring constantly. it could be caused by the dispenser solenoid. 

 

Shut off the house circuit breaker for the dishwasher to completely disconnect electrical power. Leave the breaker off for 5 minutes. Reset the breaker to restore electrical power and see if the buzzing noise continues. If it does, then you may need to replace the electronic control board in the console. Shut off the house circuit breaker before accessing and replacing internal components.

 

If you need more help, reply with additional details.

 

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services Dishwasher Repair. 

Read More
Lyle W -
Sears Technician
June 17, 2013
See more answers

Top Parts