Model #66513733K601 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Fill, Overflow And Drain Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

The cycle details on the touch panel (eg "pots/pans", "normal wash", etc) have fallen off. I don't see this as a replacement part. 66513733K601 Kenmore Dishwasher

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

This unit does not have the overlay separtely from the panel. You would need to order the control panel in order to replace those buttons.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
December 11, 2014
Q:

sporatic operation 66513733K601 Kenmore Dishwasher

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dishwasher is not working properly.

 It sounds to me like you have a stuck key and the control board would need to be replaced. 


Open key or LED circuit(s)
on the keypad, or open
circuits on the control to the
keys and LEDs.
See “Checking Keypad Operation”.
Some models do not allow
keypresses with door open.
Door switch not making
contact:
? Faulty or sloppy door
latch assembly (which can
be aggravated by high door
closure force).
? Faulty door switch (high
resistance).
? Faulty control does not
detect door closed.
1. Unplug dishwasher or disconnect
power.
2. Measure resistance of door switch
contacts while checking mechanical
operation of latch assembly. Confirm
switches not loose from assembly. Check
strike plate and door closure.
3. Check/replace control.


CHECKING KEYPAD OPERATION
A rapidly blinking LED over one of the keys of the keypad
(or sometimes a “dead” keypad/console) indicates one or
more key switch lines are stuck or shorted on either the
control or the keypad. To determine if the control or
keypad is faulty, do the following test:
1. Unplug dishwasher or disconnect power.
2. Open the dishwasher door.
3. Open console and disconnect the keypad ribbon connection from the
control (at P1). Make sure all other connections are made.
4. Put console back together. Do not close the dishwasher door.
5. Plug in dishwasher or reconnect power.
6. Wait 5 seconds.
7. Close dishwasher door.
8. Monitor the control’s response:
?If the control is OK (no longer sees shorts with the keypad
unplugged), it will respond by turning on a Drain Motor for
2 minutes. Check and/or replace the keypad if the control
responds OK.
?If the control is not OK (still sees shorts with the keypad
unplugged), then the drain motor will NOT respond and will remain
off. If no response, replace the control.
General Keypad Inspection:
Unplug dishwasher or disconnect power.
? Check keypad ribbon tail for broken/shorted/corroded/creased traces.
? Check for loose connection to control.
? Check for evidence of contaminants or corrosion around the perimeter of the keypad, on the keypad ribbon tail and/or on the keypad connector at the control.
? Perform keypad function check.
? For a final check (if possible), try replacing control/keypad with a known good control/keypad to identify where problem(s) persist.
To test the model ID diodes in the keypad:
Check each key and confirm corresponding LED turns on and that the proper delay selections for that model are available. If ID diodes for this keypad are opened or shorted, key and LED mapping and features like delay may be altered.


SERVICE DIAGNOSTICS CYCLE NOTES
NOTE 1. To invoke the Diagnostics Cycle, perform
the following key presses or actions in less than
6 seconds while in standby:
Heated Dry ? Normal ? Heated Dry ? Normal
? To rapid advance one interval at a time, press the
Start/Resume key.
? Invoking Service Diagnostics clears all status and
last ran information from memory and restores
defaults; It also forces the next cycle to be a sensor
calibration cycle.
Calibration cycles begin with a “sensor check” to determine whether the dishwasher has an OWI soil sensor or not. If the control detects an OWI, it forces two
rinses to occur prior to Final Rinse (to assure clear
water), then calibrates the OWI during the final rinse.
NOTE 2. Turn on all LEDs immediately upon
receiving entry sequence (even if door open) and
throughout this first interval as a display test.
NOTE 3. On numeric time display models, display
the following software information after the initial
display test:
? Interval 18 – Dishwasher control platform number
(“d3” Raptor/Tall Tub, “d2” Cheetah/Briva, “d1”
Rush/Tall Tub, “d0” New Gen).
? Interval 17, 16, 15 – Software generation number
(incremented for each release of software to
production).
NOTE 4. If flow meter is operating correctly the
control will turn on the Clean LED when flow meter
counts 3 or more pulses anytime during these
intervals.
NOTE 5. Thermistor (temperature sensor) checks:
? Turn Clean LED on if thermistor is in its normal
temperature range of 17°C–71°C (62°F–160°F).
? Turn sanitized LED on if thermistor is above
38°C (100°F).
NOTE 6. OWI (optical soil sensor) checks:
? Check OWI sensor for the presence of clear water
during the 5 sec. pause in interval 13 and turn on the
Clean LED in interval 12 if clear water detected.
? Check OWI sensor for the presence of air during the
last 5 sec. of Drain interval 3 and turn on the Clean LED
in interval 2 if air detected.
? Check OWI sensor for presence of bulk soil in the
water during pause interval 8; execute max. allowed
APFs and turn on Clean LED in interval 7 if bulk soil
detected.
NOTE 7. Heater relay must lag wash motor relay by
1.5 sec. at start-up of heated wash intervals to avoid
simultaneous heater and motor in-rush current.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 24, 2014
Q:

How to remove arm to get piece of glass out of soil separator 66513733k601 Kenmore Dishwasher

A:

Thank you for choosing SearsPartsDirect.com. I will be more then happy to assist you. I was able to find a video for you that shows you the soil separator and how to remove everything to get to it. Click the link below to watch. If you are not comfortable doing this repair you can Click Here to schedule a technician or call toll free 1-800-469-4663. Hope this information has help you, any further questions or concerns. You will have to post a new question because at this time I can not reply to any comments. Again, Thank you for choosing SearsPartsDirect.com.
 

Read More
Samantha A -
Sears Technician
June 04, 2014
A:

Do not see the link to click on for the video. The only one I see brought me to a clothes dryer, not a dishwasher.

Read More
Nancy -
June 05, 2014
See more answers

Top Parts