Model #66513692K600 KENMORE Dishwasher

  • Frame And Console Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Tub Assembly Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Dishrack And Water Feed Parts
    3 Results
  • Lower Dishrack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dishwasher thermal fuse. 66513692K600 Kenmore Dishwasher

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is trouble with the dishwasher
 
Glad to help out.   Im  looking at your Kenmore model number 665.13692k600.

Sorry to hear with the fuse problem.   With it happening again may be more of a board or a wire problem.  You don't want to keep buy thermal fuses every month.

The fuse could of blown because of a faulty door latch or door switch.   Could also fault by control board or bad wire.

I would highly advise  you to get a service man to come out and take a look to get it done correctly.   Good luck.

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
January 15, 2014
Q:

dishwasher not working correctly 66513692K600

A:

When the dishes are not coming out clean out of the Kenmore dishwasher, that defeats the purpose of having a dishwasher. Let's see if an adjustment of the lower spray arm will help. Check out the link provided below while waiting for additional information from an expert.

Read More
Anna T -
October 09, 2012
A:

How long does it take to get an answer?? It has been many hours.

Read More
Apryl -
October 09, 2012
A:

I know that it can be very difficult to have issues with your dishwasher. Usually this problem is going to be due to a low amount of water volume or the spray arms are not circulating enough water. Be sure the water is filling to the proper level. The water should be about half an inch from the bottom of the float. Make sure the spray arms are moving freely & the holes are not restricted. The lower spray arm should have a great deal of play in it. This is to accommodate the water pressure that will be coming out. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
October 09, 2012
A:

As I said in my original question the arms are moving freely & there is no blockage in the nozzles. Thank you for the info about the lower arm having a lot of play, it appeared to be loose but I guess not. It sounds strange that all of a sudden the water pressure would change & not be enough. How can I tell how much water is in there? I did move the float & it is moving freely as well.

Read More
Apryl -
October 09, 2012
A:

Start the dishwasher on a normal cycle and waiting for about 5 minutes. Then open the door. The water should be 1/2" from the bottom of the float, or 1/4" from the heating element. It is possible that the inlet valve is blocked and not letting enough water into the dishwasher, but if it is then the problem is most likely in the pump. Please let me know if you need anything else. Thank you for using Manage My Life.

Read More
Anonymous -
Sears Technician
October 10, 2012
See more answers
Q:

kenmore 665 dishwasher. Sani rinse, normal wash, delay start, and start buttons non responsive

A:

I can see how frustrating it would be to not have the buttons respond on the dishwasher. One of the first places I look for answers is the owner's manual. If you have the model number handy, just click on the Manuals tab below to access the online manual. While you wait for the expert to answer, you may also want to check the answer from a previous post. Just check the bottom of the expert post. Hope this helps!

Read More
Barbara H. -
August 28, 2010
A:

Thanks. I looked at the manual on line. There is nothing listed under trouble shooting for buttons not working. I actually found a way to reset. all lights on buttons light up and it kicks into some kind of short cycle. After it runs its course. I still have the same issues.

Read More
Tim -
August 28, 2010
A:

Since the control buttons won't respond, the control panel for the dishwasher is likely bad and will need to be replaced. You could also have a bad electronic control board in the console of the dishwasher that would cause this failure. A bad door switch could prevent the dishwasher from starting. You may try shutting off the breaker for the dishwasher to disconnect electrical power for a few minutes and then powering it back up. This will sometimes reboot the control board and there is a slight chance that it will begin working properly. If this does not work, you can shut off the breaker and check the wire harness connections on the control board as shown in the image below. Depending on your model number, your dishwasher may look slightly different than the one shown below.

For more help with this problem, we need to have the model number for your dishwasher. With the model number, we can normally provide more specific technical troubleshooting. Submit this additional information and any other details that you have and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 30, 2010
A:

Sorry, I should have been more speceific. The modle number is #66513692K600. I shut off the power for 10 min+ and turned back on. I still have the same problem. Not all buttons are non responsive just the ones I listed. All the others light up when you push them. I took apart the door already and checked all the conections. Everything appeared to be fine. Looking on line on other web sights. I found one blog that recomending replacing the thermal fuse. I ordered the part yesterday. Should be here by the end of the week. When I do the reset alternating pushing the buttons (that work) it kicks into a short cycle mode or something. Would it do this if the door switch was bad?

Read More
Tim -
August 30, 2010
A:

Would the control panel be bad if some buttons work?

Read More
Tim -
August 30, 2010
A:

Thanks for the model number. Your symptoms are still pointing to a failed control panel. There is still a possibility that a bad electronic control board is causing this failure. I provided a specific technical test for the key panel that you may be able to conduct if you have a volt/ohm meter and precision probes. The pin-out check of the switches on the control pad will help you determine whether you have bad keys on the control console. I recommend that you start with the START key. I provided a diagram of the pin locations in the second image below. These tips should help you check the control keypad. If you find a bad key (or keys), I recommend that you replace the control console. You can order the part from the Sears PartsDirect website (see link below). If you need more help, let us know.

Read More
Lyle W -
Sears Technician
August 30, 2010
See more answers

Top Parts