Model #66513594K600 KENMORE Dishwasher

  • Frame And Console Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Tub Assembly Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Dishrack And Water Feed Parts
    3 Results
  • Lower Dishrack Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What does the thermal fuse protect? 66513594k600 Kenmore Dishwasher

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

After researching your model it sounds like you may have and issue with the drain pump pulling to much power. I would recommend removing the drain pump and have it tested. Also check the electrical plug on the pump for burn marks that would show signs of electricity arching.

If you need further assistance, please resubmit your question with additional details. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
March 24, 2014
Q:

heated dry light flashing

A:

I understand that your dishwasher has the heated dry light on it. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
March 16, 2012
A:

Hi Trisha,

Thank you for submitting a question to Manage My Life.

Typically when the heated dry light flashes this indicates a stuck key or shorted keypad. The diagnosis of this issue will require the use of a volt/ohm meter. If you have a meter and are confident in your technical abilities please reply below and I will be happy to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website; Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance please reply to this post.

Landell

Read More
Landell -
Sears Technician
March 17, 2012
A:

I am current facing same issue, is there a resolution can be emailed so that I can verify this.

Read More
Madhu -
March 04, 2013
A:

Hello Madhu. If you have that same model number of dishwasher that is listed above (665.13594K600), then let us know and we will provide troubleshooting for that model. If you have a different model of dishwasher, then I recommend that you reply with that full model number and we will assist you further.

Read More
Lyle W -
Sears Technician
March 04, 2013
See more answers
Q:

2nd time for this question

A:

Good afternoon.... I can understand your concern and you've done a good job at trying to get to the bottom of this problem. I was unable to provide you with a diagram on your particular model number. I will forward your question to an expert who will investigate the matter further and get back to you. You will hear from them within two business days if not sooner. Until you hear from us, have a nice day.

Read More
Henry -
February 18, 2013
A:

A little more information... there are no lights on the control panel, But I do have power from the wall to the door switch through to the thermal fuse and through it to the plug on the electronic board. I could do a ohms check on the control panel's switches ribbon if I knew it's configuration, to see if the problem is there... as well as the electronics board if I could find some kind of diagram for that component.I hate to do this like a shade tree mechanic and change out parts till I fine the right one.

Read More
Aubry -
February 18, 2013
A:

Thanks Henry, I appreciate all the help I can get. Troubleshooting electrical systems on aircraft seemed easier, but then again I always had diagrams and skematics to lead the way, lol. Here is the parts list link... #6 and 16 are what I am trying to bypass and find some kind of diagrams on to check them as well. http://c.searspartsdirect.com/lis_png/PLDM/K0605011-00001.png

Read More
Aubry -
February 18, 2013
A:

Thank you for your question and I understand your concern.

 I added an image below of the wiring diagram. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
February 20, 2013
A:

Thanks Joey, A bit different than the aircraft diagrams I am used to reading, but I think I can muddle through. I do have a few question as to how to go through these circuits. The print shows at the top right my exact problem. ( Blown TCO attached to control) So where exactly do I measure the resistance and what is a TCO ? If you could break this down to a tree it would be great. From what I see, if I have power at P8(tan) and everything in the board is good through the relay, I should have power at P10(R-Bk) to the pump. And so on throughout the functions.

Read More
Aubry -
February 20, 2013
A:

Aubry: The (TCO) is the Thermal Cut Off. The TCO is connected in a series circuit between on gray wire between the door switch and the control board. If the TCO is open, the dishwasher will not power up. Disconnect the power supply before disconnecting the TCO and testing it for continuity with the Ohm meter. The image of the wiring diagram and the strip circuits should provide the information you're looking for. I do not believe you can by-pass the control to test the wash motor because it need start voltage and run voltage. The wiring diagram indicates what the Ohm resistances should measure at the motor.

Read More
Joey S -
Sears Technician
February 20, 2013
A:

Thanks for the clear up. That's what I though you were talking about. I know it as a thermal fuse. same thing just different terminology. ( I finally saw it on the diagram, need glasses, lol) I have checked it and it shows open, however when connected and power is on I get power through it to P8 {pwr for loads}. Would that not indicate the fuse or TCO is good? Tomorrow I will reconnect everything and check for pwr at P7, P10 to the motor and on. as well as the proper resistances, using the diagram before I start ordering parts. Thanks again for your valuable time and efforts on my behalf. I agree, at first glance it would seem to be a blown TCO, due to the open, but with power going through it??? I will let you know what I find after going through it.

Read More
Aubry -
February 20, 2013
A:

Success achieved!!! Had power through TCO to P8, but not to P7 . Also no power on P9 of the fill circuit. I removed the circuit board from it's plastic holder and checked the soldering underneath. and there it was.... a crack in the joint below P8........A quick heating of the joint and WALLAH... I had display lights. pushing the Start button and the water started to flow.... YEAH!!!... Looks like a vibration problem and a weak solder joint. I will purchase a new TCO and install it as a precaution, but you just saved me at least the cost of a new control panel $126 and/ or a new control board $83 or the service repair bill of over $200 Thanks Joey...... you are a gem.

Read More
Aubry -
February 21, 2013
A:

Aubry: You did a great job of diagnosing the failure. Have a great day.

Read More
Joey S -
Sears Technician
February 21, 2013
A:

Thanks and you too....If you ever need to learn something about how to fix a military aircraft let me know, lol

Read More
Aubry -
February 22, 2013
See more answers

Top Parts