Model #66513469K902 KENMORE Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel And Latch Parts
    3 Results
  • Inner Door Parts
    3 Results
  • Fill, Drain, And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Heater Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Lower Washarm Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore dishwasher model 665 wont start a wash cycle worked fine yesterday today all lights were on, cancel drainpump worked but will not wash Any Suggestions??

A:

I know how important it is to have a good working dishwasher in the home since dirty dishes tend to gather quickly. While you are waiting for an expert answer, I did manage to find a link that provides some great tips about fixing a similar problem to the one that you are having. I hope my link is useful.

Read More
Joseph P. -
December 29, 2010
A:

Thank you, for your question.

I am sorry you are having a problem with your dishwasher. Without a model number, I will only be able to give general information. Usually when the lights are rapidly flashing on the console and the dishwasher will not start, it is because of a shorted key on the touch pad. Some models have a check that can be done to confirm this problem. I recommend turning the power off to the dishwasher for five minutes and the retest the operation. if the dishwasher does the same thing please reply below with a complete model number and I will be happy the assist you further with this problem.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 31, 2010
A:

I have a Kenmore Mod # 665.13469K902. The start button no longer works. Any ideas if I can fix this myself?

Read More
Lore -
July 16, 2013
A:

Lore: I must assume the "Lock On" LED is not lit indicating the controls are in a lock out and there are no flashing LED's. If the control panel will power up and your able to select cycles but will not start, the door may not be latching properly to close the door switch. It could also have a faulty touch panel/control panel too. The door switch operation will need to be tested as well as the door switch(s). If the door is latching and the door switch(s) are Okay, then I would test the "Start button switch" operation using the image below. You will need an Ohm meter to test the "Start" switch on the control panel. Disconnect the dishwasher from the power source before removing the control panel. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service by calling Sears at 1-800-4-MY-HOME.

Read More
Joey S -
Sears Technician
July 16, 2013
A:

Did some diagnostic work on dishwasher [model665.13469K902] disconnected the control board from touch control panel , powered unit up and the drain motor runs..but that's all . Does that sound like the touch control panel is bad? Are there any other tests that can be run on the touch control panel to confirm? Don't want to buy a part I don't need. Thanks for the help. Bob

Read More
Janet -
August 23, 2015
A:

Did some diagnostic work on dishwasher [model665.13469K902] disconnected the control board from touch control panel , powered unit up and the drain motor runs..but that's all . Does that sound like the touch control panel is bad? Are there any other tests that can be run on the touch control panel to confirm? Don't want to buy a part I don't need. Thanks for the help. Bob

Read More
Janet -
August 23, 2015
See more answers
Q:

No power 66513469K902 Kenmore Undercounter dishwasher

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your dishwasher is not working properly.

I have attached the instructions to check the keypad and control board.

 
You can also visit searpartsdirect.com for parts, diagrams, and repair information.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 26, 2015
A:
Natasha12 -
Sears Technician
July 26, 2015
See more answers
Q:

Dishwasher Display errors - Model 13469 66513469K902 Kenmore Undercounter dishwasher

A:

Based on your symptom and details I suspect a faulty control panel. The key pad/control panel can be tested with an Ohm meter using the information I added in the image below. I recommend checking the "Cancel Drain" and the "Normal" cycle buttons first. If either one measures continuity without pushing the key pad; replace the console assembly. If the keys are not shorted, the control board will need to be replaced.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

If you do not feel confident repairing this problem yourself, you can have it repaired at your home by a Sears technician. Click here is a link for the website: Sears Home Services .

If you have another question or have more information to share, click on the "join the conversation" box to provide any information, then click reply. This is the best and fastest way to contact me. This will also speed up the process for you.

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com
Read More
Sherman_G_Wallace -
Sears Technician
November 08, 2013

Top Parts